Authorized ABB Distributor (Installation Products)
ABB - Installation Products 273DRGA-PGE - 200 Amp, 25kV, Insulated Cap with Ground, Equipped with Insulated Cuff, without Probe. For PGE

ABB Installation Products 273DRGA-PGE 200 Amp, 25kV, Insulated Cap with Ground, Equipped with Insulated Cuff, without Probe.…

UPC: 783786367962


Documents & Media
Installation InstructionsSpecification SheetManufacturer Product Website

Contact for Pricing

Minimum Qty: 20

Multiplier: 20

*Contact for lower quantities*

Call +1 (262) 252-1600 (toll-free 877-268-3700) or email [email protected] for pricing and availability.

Overview

The ABB 273DRGA-PGE is a 25kV class, 200 Amp loadbreak insulated cap designed for energized operation. This fully shielded, fully submersible separable connector features an integral ground lead and an insulated cuff for enhanced operator protection. It meets ANSI/IEEE Standard 386 and is suitable for use on 25kV class loadbreak systems. The cap is designed to dead-end Elastimold® mating products such as bushing inserts, feed-thrus, and junctions. Key specifications include a maximum phase-to-ground operating voltage of 15.2kV, a maximum phase-to-phase voltage of 26.3kV, and an impulse withstand of 125kV BIL. It offers a 40kV AC one-minute withstand and 78kV DC fifteen-minute withstand, with corona extinction at 19kV AC @ 3pC sensitivity. The continuous and loadbreak current rating is 200 Amps, with a 10kA symmetrical momentary and fault close rating for 10 cycles. Constructed from molded EPDM rubber, this insulated cap is provisioned for hot stick operation and includes a #14 AWG ground lead wire. The 273DRGA-PGE model is specifically equipped with an insulated cuff and is available without a probe, simplifying installation. This component is ideal for pad-mounted transformers, switchgear, and underground cable terminations in industrial, utility, and commercial environments. SKU: 273DRGA-PGE.
  • 25kV, 200 Amp Loadbreak Rated
  • Molded EPDM Rubber Construction
  • Integral Ground Lead Wire (#14 AWG) Attached
  • Insulated Cuff for Enhanced Protection
  • Fully Shielded, Fully Submersible, Hot Stick Operable

Specifications

Amperage Rating
200 A
Application
Fully shielded, fully submersible, hot stick operable, separable connectors designed for energized operation
Color
Black
Current Rating
200 A
Insulation
True
Material
Housing - EPDM-Rubber
Size
Diameter 2.90 inch (73.7mm)
Special Features
25kV, 200 Amp Loadbreak Rated. Molded EPDM Rubber. Includes all brass probe. Provision for hotstick operation. Ground lead wire #14 AWG attached. Insulated cuff for extra protection
Standard
ANSI/IEEE Standard 386
Temperature Rating, Maximum
149 F
Temperature Rating, Maximum
65 C
Temperature Rating, Minimum
-40 F
Temperature Rating, Minimum
-40 C
Type
Loadbreak Insulated Cap
Voltage Rating
25 kV
Package Dimensions (L x W x H)
0.01 IN x 0.01 IN x 0.01 IN
Package Dimensions (L x W x H)
0.0254 cm x 0.0254 cm x 0.0254 cm
Package Weight (Imperial)
1.5000 L
Package Weight (Metric)
0.6800 kg
600 Amp, 15/25kV, 600 Series Deadbreak, Elbow with Insulated Plug, Cap, Stud, Lug and Cable Adapter. Aluminum Compression Lug. Cable Insulation Diameter 0.850 inch to 1.050 inch. Conductor Size AWG Compressed Stranded 1/0 or Compacted Solid 2/0.

K655LR-H0240

600 Amp, 15/25kV, 600 Series Deadbreak, Elbow with Insulated Plug, Cap, Stud, Lug and Cable Adapter. Aluminum Compression Lug. Cable Insulation Diameter 0.850 inch to 1.050 inch. Conductor Size AWG Compressed Stranded 1/0 or Compacted Solid 2/0.
200 Amp, 25kV, Insulated Cap with Ground, Equipped with Insulated Cuff, without Probe. White Band

273DRGA

200 Amp, 25kV, Insulated Cap with Ground, Equipped with Insulated Cuff, without Probe. White Band
200 Amp, 25kV, Loadbreak 4 Point Junction. With U Straps. White Band.

274J4-WB-5

200 Amp, 25kV, Loadbreak 4 Point Junction. With U Straps. White Band.
200 Amp, 25kV, Loadbreak 3 Point Junction. With U Straps. White Band

274J3-WB-5

200 Amp, 25kV, Loadbreak 3 Point Junction. With U Straps. White Band
15/25kV 600 Series Deadbreak 2-Way L-Kit. Includes Two 600 Amp Basic Elbows, Two 28 kV 600 Amp Studs, Two Insulated Plugs with Caps, Compound and Instructions

K655L2

15/25kV 600 Series Deadbreak 2-Way L-Kit. Includes Two 600 Amp Basic Elbows, Two 28 kV 600 Amp Studs, Two Insulated Plugs with Caps, Compound and Instructions
15/25kV 600 Series Deadbreak 3-Way L-Kit

K655L3

15/25kV 600 Series Deadbreak 3-Way L-Kit
15/25kV 600 Series Deadbreak 1-Way L-Kit. Includes 600 Amp Basic Elbow, 28 kV 600 Amp Stud, Two Insulated Plugs with Caps, Compound and Instructions

K655L1

15/25kV 600 Series Deadbreak 1-Way L-Kit. Includes 600 Amp Basic Elbow, 28 kV 600 Amp Stud, Two Insulated Plugs with Caps, Compound and Instructions
600 Amp, 35kV, 600 Series Deadbreak 2-Way L-Kit. Does not include cable adapters or compression lugs, must be ordered separately.

755L2

600 Amp, 35kV, 600 Series Deadbreak 2-Way L-Kit. Does not include cable adapters or compression lugs, must be ordered separately.

Frequently Asked Questions

Does this cap include an insulated cuff?

Yes, the 273DRGA-PGE is equipped with an insulated cuff for added protection.

What is the voltage rating of this insulated cap?

The insulated cap is rated for 25kV, suitable for medium-voltage applications.

What is the current rating of this cap?

The cap supports a continuous current rating of 200 Amps.

Is a probe required for this insulated cap?

No, the cap is designed without a probe, simplifying installation.

Is this cap compatible with PGE standards?

Yes, the 273DRGA-PGE is specifically designed for PGE applications.

How to Install the 273DRGA-PGE Insulated Cap with Ground Lead

Instructions for installing and removing the 273DRGA-PGE insulated cap with ground lead on ELASTIMOLD loadbreak bushing interfaces.

Estimated time: 30m

Tools needed:

Hotstick (minimum 8 ft length recommended), System ground connection tool

Supplies needed:

Insulated Cap with Ground Lead, Lubricant (supplied or ELASTIMOLD approved), Protective cover

  1. Connect the electrostatic grounding wire

    Connect the free end of the electrostatic grounding wire to the system ground. Ensure there is enough slack for hot-stick operation. CAUTION: Train the grounding wire so it does not contact the bushing interface during operation. WARNING: If the ground lead disconnects during operation, do not attempt to reattach without first pulling the insulated cap off the bushing with the hotstick.

  2. Prepare the insulated cap

    Remove the protective cover from the insulated cap. Lubricate the cap's internal mating surface using only the supplied lubricant or ELASTIMOLD approved lubricants. DO NOT SUBSTITUTE. Keep the internal mating surface free from dirt and grime. Always replace the protective cover when not in use.

  3. Install the insulated cap

    Firmly attach a hotstick to the insulated cap pulling eye. Insert the male contact of the insulated cap into the loadbreak bushing. Push home with a fast, firm, straight motion, ensuring it is fully mated and the locking ring is seated. Detach the hotstick from the insulated cap.

  4. Remove the insulated cap

    Attach the hotstick to the pulling eye. Rotate the insulated cap slightly while in the mated position to break surface friction. Pull the receptacle off with a fast, firm, straight motion. Remove the electrostatic grounding wire of the insulated cap from the system ground. Replace the protective cover on the insulated cap to keep its internal surface clean.

Frequently Asked Questions about ABB - Installation Products

How are Thomas and Betts products typically installed?

Thomas and Betts products are installed using a variety of methods tailored to specific applications, including the use of flexible cords and cable fittings, non-metallic cable glands, and armored cable fittings. Proper selection of fittings is crucial to match the cable type and installation environment, ensuring durability and preventing physical damage. Tools such as the Blackburn® Comfort Crimp® and HEX-FLEX® systems enhance installation efficiency and reliability, reducing labor time and ensuring secure connections.

What accessories are available for Thomas and Betts products?

Thomas and Betts offers a comprehensive range of accessories for their products, including various cord and cable fittings, non-metallic cable glands, service entrance cable fittings, and armored cable fittings. Their accessories are designed to enhance installation efficiency and ensure compatibility with different cable types and environmental conditions, providing reliable connections for a wide array of applications.

What environmental ratings do Thomas and Betts products have?

Thomas and Betts products feature robust environmental ratings, including NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications, as well as IEC 60529 IP66 protection. These ratings ensure that their products are designed to withstand harsh industrial environments, with capabilities to resist dust, water, and corrosion, and operate effectively in a wide temperature range.

What communication protocols do Thomas and Betts products support?

Thomas and Betts products support a wide range of industrial communication protocols, including Ethernet, DeviceNet, PROFIBUS, Modbus, CANopen, and others. This extensive compatibility ensures seamless integration and reliable communication across various industrial automation systems, catering to diverse application needs.

What are the key features of Thomas and Betts products?

Thomas and Betts products are known for their innovative designs, high performance, and compliance with industry standards such as the National Electrical Code and Underwriters' Laboratories. They offer a comprehensive range of rugged and reliable electrical fittings, including liquidtight and dust-tight connections, which enhance installation efficiency and reduce overall project costs. Their products are engineered for durability in harsh environments, ensuring long-term reliability and lower installed costs.

What are the main product lines offered by Thomas and Betts?

Thomas and Betts offers a comprehensive range of product lines including electrical connectors, cable management systems, grounding and bonding solutions, and industrial automation components. Their products are designed for durability and reliability in demanding industrial environments, ensuring optimal performance and safety across various applications.

What technical support does Thomas and Betts offer?

Thomas and Betts offers comprehensive technical support, including access to field application engineers for onsite training and installation assistance. Their technical support staff is available to address inquiries related to product specifications and installation practices, ensuring optimal performance and safety of electrical systems. Additionally, they provide a variety of training programs to enhance the knowledge and skills of users in the field.

What industries and applications are Thomas and Betts products used for?

Thomas and Betts products are utilized across various industries including electrical construction, industrial automation, telecommunications, and utilities. Their extensive range of cord and cable fittings, electrical boxes, and metal framing systems are designed for applications that require durability and reliability in harsh environments, ensuring optimal performance in both permanent and temporary installations.

What certifications and standards do Thomas and Betts products comply with?

Thomas and Betts products comply with critical international certifications including UL (Underwriters Laboratories), CSA (Canadian Standards Association), and CE (European Community). Our products are designed to meet rigorous industrial standards such as NEMA enclosure ratings and IEC 60529 IP ratings, ensuring safety and reliability across various industrial applications.

What are the main product lines offered by Ocal?

Ocal offers a comprehensive range of corrosion-resistant conduit systems, including PVC-coated conduit and fittings, conduit bodies, hazardous location fittings, and strut accessories. Their products are designed to provide superior corrosion protection, featuring a hot-dipped galvanizing process and UL listed Type 4X PVC-coated conduit bodies, ensuring durability in the most demanding environments.