
ABB Installation Products 274RLR-J-5270 25kV 200 Amp, Loadbreak Replacement Elbow Connector with Test Point. .980 inch - 1.880…
UPC: 783786656394
Contact for Pricing
Call +1 (262) 252-1600 (toll-free 877-268-3700) or email [email protected] for pricing and availability.
Overview
- 25kV, 200 Amp continuous and loadbreak rating
- Extended-length housing (+10.5") for short cables
- Bi-metal compression lug for dissimilar conductor compatibility
- Non-corrosive capacitive test point for safe circuit testing
- Fully shielded, submersible molded rubber housing
- Meets ANSI/IEEE Standard 386 with 125kV BIL impulse rating
- Supports cable insulation diameters from 0.980" to 1.880"
- Provisions for hot stick operation and ground wire connection
Specifications
Amperage Rating | 200 A |
Application | 25kV, 200 Amps |
Color | Blue |
Color | Black |
Conductor Range | 4/0 STR/COMPR AWG , 250 kcmil |
Connection Type | Compression Lug |
Connection Type | Compression |
Current Rating | 200A |
Current Rating | 200 A |
Environmental Conditions | Fully Submersible |
Insulation | True |
Material | Bi-Metal Compression Lug |
Material | Bi-Metal |
Material | Housing - EPDM-Rubber |
Series | 274RLR |
Size | 0.980 inch - 1.880 inch |
Size | 0.980" - 1.880" |
Size | Cable Insulation Diameter 0.980 inch to 1.180 inch |
Special Features | Replacement Elbow has extended length contact and elbow housing resulting in a net gain of 8-7/8 inches in length. Includes 00400X long Bi-Metal Contact |
Standard | ANSI/IEEE Standard 386 |
Temperature Rating, Maximum | 149 F |
Temperature Rating, Maximum | 65 C |
Temperature Rating, Minimum | -40 F |
Temperature Rating, Minimum | -40 C |
Type | Loadbreak Replacement Elbow Connector with Test Point |
Voltage Rating | 25 kV |
Voltage Rating | 25kV |
Package Dimensions (L x W x H) | 0.01 IN x 0.01 IN x 0.01 IN |
Package Dimensions (L x W x H) | 0.0254 cm x 0.0254 cm x 0.0254 cm |
Package Weight (Imperial) | 4.5100 L |
Package Weight (Metric) | 2.0460 kg |

656LRTP-J5270
600 Series Elbows with IEEE 386 Capacitive Test Points, 600 Amp, 15kV, Stick-OP Elbow Connector Kit. Cable Insulation Diameter 0.980 inch to 1.180 inch. Bi-Metal Compression Lug. Conductor Size AWG or kcmil, Compressed Stranded 4/0 /Compacted Solid 250 /mmSquared Compact 125.
274ELR-K5240
200 Amp, 25kV, Loadbreak Repair Elbow Connector with Test Point, Repair Elbow has extended length contact and elbow housing resulting in a net gain of 3-1/4 inches in length. Includes 02509X long Bi-Metal Contact. Cable Insulation Diameter 1.090 inch to 1.310 inch. Conductor Size AWG Compressed Stranded 1/0 /Solid 2/0 /mmSquared 53.49.
376LR-K-5270-S
35kV 200 Amp, Loadbreak Elbow Connector with Test Point, Cable Insulation Diameter 1090 inch to 1.310 inch. Bi-Metal Compression Lug. Conductor Size AWG Compressed Stranded 4/0 /Solid 250 /mmSquared 126.67. 200ECS Jacket Seal Included.
167RLR-G-5250-S
200 Amp, 15kV, Loadbreak Replacement Elbow Connector without Test Point, Cable Insulation Diameter 0.760 inch to 0.950 inch. Bi-Metal Compression Lug. Conductor Size AWG Compressed Stranded 2/0 /Solid 3/0 /mmSquared 67.43. 200ECS Jacket Seal Included.
167RLR-H-5250
200 Amp, 15kV, Loadbreak Replacement Elbow Connector without Test Point, Cable Insulation Diameter 0.850 inch to 1.050 inch. Bi-Metal Compression Lug. Conductor Size AWG Compressed Stranded 2/0 /Solid 3/0 /mmSquared 67.43.
274RLR-H-5220
25kV 200 Amp, Loadbreak Replacement Elbow Connector with Test Point. Cable Insulation Diameter 0.850 inch to 1.050 inch. Bi-Metal Compression Lug. Conductor Size AWG Compressed Stranded #2/Solid #1/mmSquared 33.62.Frequently Asked Questions
What is the current rating of these elbow connectors?
The Elastimold repair and replacement elbow connectors are rated for 200 amps.
What is the catalog number for the test point cap?
The catalog number for the test point cap is 156-7.
Where are Elastimold 200 A elbows manufactured?
Elastimold 200 A repair and replacement elbows are designed, molded, and tested in Albuquerque, New Mexico, USA.
What is the cable insulation diameter range for 274RLR-J?
For the 274RLR-J model, the cable insulation diameter ranges from 0.980 inches to 1.180 inches.
Are these elbow connectors compliant with industry standards?
Yes, they are IEEE 386 compliant, ANSI certified, and Rural Utilities Service (RUS) accepted.
Do these elbows include a test point feature?
Both repair and replacement elbows are available with an optional built-in capacitive test point for testing the circuit for voltage presence.
How much extra length does the repair elbow provide?
The repair elbow provides a net gain of 3 1⁄4 inches in length compared to a standard elbow.
How much extra length does the replacement elbow provide?
The replacement elbow provides a net gain of 8 7⁄8 inches in length compared to a standard elbow.
What voltage classes are available for these elbows?
These loadbreak repair and replacement elbows are available for 15 kV and 25 kV voltage classes.
What type of contact is included with the 274RLR elbow?
The 274RLR replacement elbow includes a long bi-metal contact, catalog number 00400X.
How to Install the 274RLR Loadbreak Replacement Elbow Connector
This guide provides step-by-step instructions for the safe installation and initial setup of the Elastimold 274RLR Loadbreak Replacement Elbow Connector, converting a livefront termination to deadfront for UD cable with concentric neutral and extruded insulation shielding.
Estimated time: 1h 30m
Tools needed:
Probe Wrench, Wire brush, Wrench, Hotstick type live-line tool, Suitable sensing device (for capacitive test points)
Supplies needed:
Replacement Elbow Connector Housing, Compression Lug, Probe, Lubricant (supplied, do not substitute), Hose Clamp, Copper wire (No. 14 AWG / 2.5mm or equivalent), Appropriate connector (for ground lead), Silicone grease (for test point cap)
- Perform Initial Checks and Gather Materials
Verify that all package contents are complete and undamaged. Check all components for proper fit with the cable and mating products. Thread the probe into the compression lug to check for resistance; replace damaged components if resistance is encountered. Read all installation instructions thoroughly before starting and ensure all required tools are at hand, maintaining cleanliness throughout the procedure.
- De-energize Apparatus and Remove Livefront Terminator
DANGER: All apparatus MUST be de-energized during installation or removal of parts. Remove the rubber cap from the existing terminator. Cut off the connector at the top of the terminator. Disconnect the ground lead from the base of the terminator. Finally, remove the terminator housing from the cable.
- Prepare the Cable
Train the cable to be straight and in-line with the bushing centerline. Cut the cable to measure precisely 10-1/2 inches from the bushing centerline. Remove 1-3/8 inches of cable insulation from the end, ensuring to cut squarely and NOT to nick the conductor. If the insulation shield measures less than 6-1/2 inches, proceed; if greater, consult an ELASTIMOLD representative.
- Install Compression Lug
Wire brush the bare aluminum conductor immediately after preparation. Install the compression lug, rotating it to spread the inhibitor. Position the lug so its contact threaded hole aligns with the bushing bore. Crimp the lug according to the crimp chart, starting at the crimp line mark and rotating 180 degrees for each successive crimp. Carefully wipe any excessive inhibitor from the outside of the lug and cable.
- Assemble Elbow Housing
Lubricate the cable insulation and the inside of the elbow housing with the supplied lubricant ONLY; DO NOT SUBSTITUTE other lubricants as they may be harmful. Keep the insulation clean and avoid introducing excess grease into the gap between the lug and insulation. Slide the elbow connector onto the cable using a back-and-forth twisting motion. Wipe off all excess grease.
- Install and Tighten Probe
Align the elbow with the compression lug's threaded hole. Thread the probe into the lug by hand, taking care not to cross-thread. The probe must turn freely for approximately four turns before becoming snug. Tighten the probe with the supplied wrench until the wrench bends, indicating proper torque.
- Connect Concentric Neutral
Insert one end of a separate copper wire (No. 14 AWG / 2.5mm or equivalent) through the grounding eye on the elbow and twist it tightly, taking care not to damage the eye. Twist all neutral wires together and connect them to ground using an appropriate connector. Provide adequate slack in the wires for elbow operation. Add the supplied hose clamp as shown and tighten it snugly, but do not overtighten.
- Connect Elbow to Bushing Plug
LUBRICATE ONLY IF THE TRANSFORMER AND ELBOW ARE KNOWN TO BE DE-ENERGIZED. Lubricate the receptacle portion of the elbow connector and the mating bushing with the supplied lubricant. Operate the elbow using a full insulated 'hotstick' type live-line tool; DO NOT OPERATE BY HAND. After establishing firm footing and positive control, place the elbow connector receptacle over the bushing plug, inserting the male contact until slight resistance is felt. Immediately push the elbow home with a fast, firm, straight motion to engage the internal lock on the elbow and bushing interface.
- Perform Voltage Test (274RLR ONLY)
For 274RLR models, remove the test point cap with a hotstick, peeling it off at an angle. WARNING: The voltage test point is a capacitance device, not directly connected to the conductor. Do not use conventional voltage measuring equipment. Use a suitable sensing device made for capacitive test points to determine if the cable is energized, following the manufacturer's directions. Treat the elbow as energized until a 'no voltage' indication is confirmed by other means. After testing, clean and lubricate the inside surface of the cap with silicone grease and replace it tightly on the test point.
Frequently Asked Questions about ABB - Installation Products
How are Thomas and Betts products typically installed?
Thomas and Betts products are installed using a variety of methods tailored to specific applications, including the use of flexible cords and cable fittings, non-metallic cable glands, and armored cable fittings. Proper selection of fittings is crucial to match the cable type and installation environment, ensuring durability and preventing physical damage. Tools such as the Blackburn® Comfort Crimp® and HEX-FLEX® systems enhance installation efficiency and reliability, reducing labor time and ensuring secure connections.
What accessories are available for Thomas and Betts products?
Thomas and Betts offers a comprehensive range of accessories for their products, including various cord and cable fittings, non-metallic cable glands, service entrance cable fittings, and armored cable fittings. Their accessories are designed to enhance installation efficiency and ensure compatibility with different cable types and environmental conditions, providing reliable connections for a wide array of applications.
What environmental ratings do Thomas and Betts products have?
Thomas and Betts products feature robust environmental ratings, including NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications, as well as IEC 60529 IP66 protection. These ratings ensure that their products are designed to withstand harsh industrial environments, with capabilities to resist dust, water, and corrosion, and operate effectively in a wide temperature range.
What communication protocols do Thomas and Betts products support?
Thomas and Betts products support a wide range of industrial communication protocols, including Ethernet, DeviceNet, PROFIBUS, Modbus, CANopen, and others. This extensive compatibility ensures seamless integration and reliable communication across various industrial automation systems, catering to diverse application needs.
What are the key features of Thomas and Betts products?
Thomas and Betts products are known for their innovative designs, high performance, and compliance with industry standards such as the National Electrical Code and Underwriters' Laboratories. They offer a comprehensive range of rugged and reliable electrical fittings, including liquidtight and dust-tight connections, which enhance installation efficiency and reduce overall project costs. Their products are engineered for durability in harsh environments, ensuring long-term reliability and lower installed costs.
What are the main product lines offered by Thomas and Betts?
Thomas and Betts offers a comprehensive range of product lines including electrical connectors, cable management systems, grounding and bonding solutions, and industrial automation components. Their products are designed for durability and reliability in demanding industrial environments, ensuring optimal performance and safety across various applications.
What technical support does Thomas and Betts offer?
Thomas and Betts offers comprehensive technical support, including access to field application engineers for onsite training and installation assistance. Their technical support staff is available to address inquiries related to product specifications and installation practices, ensuring optimal performance and safety of electrical systems. Additionally, they provide a variety of training programs to enhance the knowledge and skills of users in the field.
What industries and applications are Thomas and Betts products used for?
Thomas and Betts products are utilized across various industries including electrical construction, industrial automation, telecommunications, and utilities. Their extensive range of cord and cable fittings, electrical boxes, and metal framing systems are designed for applications that require durability and reliability in harsh environments, ensuring optimal performance in both permanent and temporary installations.
What certifications and standards do Thomas and Betts products comply with?
Thomas and Betts products comply with critical international certifications including UL (Underwriters Laboratories), CSA (Canadian Standards Association), and CE (European Community). Our products are designed to meet rigorous industrial standards such as NEMA enclosure ratings and IEC 60529 IP ratings, ensuring safety and reliability across various industrial applications.
What are the main product lines offered by Ocal?
Ocal offers a comprehensive range of corrosion-resistant conduit systems, including PVC-coated conduit and fittings, conduit bodies, hazardous location fittings, and strut accessories. Their products are designed to provide superior corrosion protection, featuring a hot-dipped galvanizing process and UL listed Type 4X PVC-coated conduit bodies, ensuring durability in the most demanding environments.
