Authorized ABB Distributor (Installation Products)
ABB - Installation Products SLK 3 A - Aluminum Compression StreetLight Kit, Run #8-#6 Aluminum, Tap #8-#6 Aluminum. Includes Insulating Cap and Rocket, Wood Dowel, (2) Tin Plated Fuse Clips, Instruction Sheet and Silicone Grease.

ABB Installation Products SLK 3 A Aluminum Compression StreetLight Kit, Run #8-#6 Aluminum, Tap #8-#6 Aluminum. Includes…

UPC: 783786752386


Documents & Media
Installation InstructionsManufacturer Product Website

Contact for Pricing

Minimum Qty: 50

Multiplier: 50

*Contact for lower quantities*

Call +1 (262) 252-1600 (toll-free 877-268-3700) or email [email protected] for pricing and availability.

Overview

The ABB SLK 3 A Aluminum Compression StreetLight Kit (SKU: SLK 3 A) is a precision-engineered solution for secure, weatherproof electrical connections in outdoor street lighting systems. Designed for aluminum conductors ranging from #8 AWG to #6 AWG, this kit ensures reliable performance in demanding environments where moisture resistance and corrosion prevention are critical. The kit includes a line-end assembly, load-end assembly, two tin-plated fuse clips, an insulating cap and rocket for watertight sealing, a wood dowel for proper alignment, and a packet of silicone grease to prevent oxidation and ease installation. Each component is rated for 600 volts, making it suitable for high-voltage street lighting circuits. The compression technology delivers mechanical strength and superior electrical conductivity, while the Flood-Seal® rocket ensures a durable, IP-rated seal against environmental contaminants. Installation is straightforward: strip 3/4" of insulation, apply silicone grease, insert the conductor into the line-end assembly, torque the set screw to 25 in-lbs, and mate the housings for a secure connection. The SLK 3 A is ideal for municipal street lighting, highway illumination, and commercial outdoor lighting projects where long-term reliability and minimal maintenance are priorities. Manufactured by ABB - Installation Products, the SLK 3 A meets the rigorous demands of outdoor electrical infrastructure with a focus on durability, safety, and ease of use.
  • For #8 to #6 AWG aluminum conductors in street lighting applications
  • Includes line-end and load-end assemblies, tin-plated fuse clips, insulating cap, rocket, wood dowel, and silicone grease
  • Rated for 600 volts with compression technology for mechanical strength and conductivity
  • Flood-Seal® rocket provides IP-rated watertight protection against environmental contaminants
  • Torque set screw to 25 in-lbs for secure conductor connection

Specifications

Application
Rated 600 Volts, 30 Amps Maximum, perfect for heavy-duty applications
Conductor Range
#8 to #6 AWG
Connection
Compression
Connection Type
Compression
Finish
Bare
Insulation
EPDM Rubber
Material
Aluminum
Number of Conductors
2
Series
SLK
Size
#8 AWG to #6 AWG
Special Features
Includes Insulating Cap and Rocket
Type
Breakaway Street Light Kit Non-Fused
Package Dimensions (L x W x H)
0.01 IN x 0.01 IN x 0.01 IN
Package Dimensions (L x W x H)
0.0254 cm x 0.0254 cm x 0.0254 cm
Package Weight (Imperial)
0.1300 L
Package Weight (Metric)
0.0590 kg
600 Amp, 15/25kV, 600 Series Deadbreak, Elbow with Insulated Plug, Cap, Stud, Lug and Cable Adapter. Aluminum Compression Lug. Cable Insulation Diameter 0.980 inch to 1.180 inch. Conductor Size kcmil Compressed/Stranded 500 or Compact/Solid 600 or mm2 Compact 250/300.

K655LR-J0330

600 Amp, 15/25kV, 600 Series Deadbreak, Elbow with Insulated Plug, Cap, Stud, Lug and Cable Adapter. Aluminum Compression Lug. Cable Insulation Diameter 0.980 inch to 1.180 inch. Conductor Size kcmil Compressed/Stranded 500 or Compact/Solid 600 or mm2 Compact 250/300.
Single cable clamp 150-300mm2 for power terminal type 5

45000034

Single cable clamp 150-300mm2 for power terminal type 5
Flood Seal In Line Disconnect Kit, Single Housing. Includes Santoprene Insulating Cap and Rocket, Wood Dowel, (2) Tin Plated Copper Fuse Clips, (2) Copper Wire Stranded #14 x 19-3/4 inch, Silicone Grease.

SLK 6-8488

Flood Seal In Line Disconnect Kit, Single Housing. Includes Santoprene Insulating Cap and Rocket, Wood Dowel, (2) Tin Plated Copper Fuse Clips, (2) Copper Wire Stranded #14 x 19-3/4 inch, Silicone Grease.
Aluminum Mechanical Streetlight kit. Includes (2) Insulating Rockets trimmed at #14 - #10 Ring, (2) Fuse Clips, (1) Line End, (1) Load End, (2) #2 - #14 Wire Ends with Screws - 5/16-24 x 3/8 inch, Silicone Grease and Installation Instructions.

SLK 22 M 10 CAB

Aluminum Mechanical Streetlight kit. Includes (2) Insulating Rockets trimmed at #14 - #10 Ring, (2) Fuse Clips, (1) Line End, (1) Load End, (2) #2 - #14 Wire Ends with Screws - 5/16-24 x 3/8 inch, Silicone Grease and Installation Instructions.
Mechanical Fuse Kit Inline, Includes EPDM Rubber Finished Rocket and Twin Cap, Silicone Grease, Copper Wire #10,7 X 37/34. One Tin Plated Copper Fuse Holder with 5/16-24 Aluminum Set Screw with 1/8 Hex, One Tin Plated Aluminum Mechanical Splice with Three Stainless Steel 1/4-28 x 3/8 inch Screws. Accepts Standard Non-Glass Type Cartridge Fuse with 13/32 inch Diameter and 1-1/2 inch Length. Wire Range #12 to #4 CU-AL AWG.

SLK-YM

Mechanical Fuse Kit Inline, Includes EPDM Rubber Finished Rocket and Twin Cap, Silicone Grease, Copper Wire #10,7 X 37/34. One Tin Plated Copper Fuse Holder with 5/16-24 Aluminum Set Screw with 1/8 Hex, One Tin Plated Aluminum Mechanical Splice with Three Stainless Steel 1/4-28 x 3/8 inch Screws. Accepts Standard Non-Glass Type Cartridge Fuse with 13/32 inch Diameter and 1-1/2 inch Length. Wire Range #12 to #4 CU-AL AWG.
Tin Plated Aluminum Mechanical Streetlight kit, Run #10 - #4 Aluminum and Copper, Tap #10 - #4 Aluminum and Copper. Includes Insulating Cap and Rocket, Wood Dowel, (2) Tin Plated Aluminum Fuse Clips with Screws, Silicone Grease and Instruction Sheet

SLK 60 M

Tin Plated Aluminum Mechanical Streetlight kit, Run #10 - #4 Aluminum and Copper, Tap #10 - #4 Aluminum and Copper. Includes Insulating Cap and Rocket, Wood Dowel, (2) Tin Plated Aluminum Fuse Clips with Screws, Silicone Grease and Instruction Sheet
Flood Seal, YY Type Fused Disconnect StreetLight Kit, #14-#4 Copper, #14-#2 Aluminum includes Insulating Twin Cap and Twin Rocket, Fuse Clip, Copper Wire 10 Gauge, (3) Screws, Silicone Grease, Oxide Inhibitor, Instruction Sheet

YFU

Flood Seal, YY Type Fused Disconnect StreetLight Kit, #14-#4 Copper, #14-#2 Aluminum includes Insulating Twin Cap and Twin Rocket, Fuse Clip, Copper Wire 10 Gauge, (3) Screws, Silicone Grease, Oxide Inhibitor, Instruction Sheet
Flood Seal, YY Type NonFused Disconnect StreetLight Kit, #14-#4 Copper, #14-#2 Aluminum, includes Insulating Twin Cap and Twin Rocket, Fuse Clip, Copper Wire 10 Gauge, (3) Screws, Silicone Grease, Oxide Inhibitor, Instruction Sheet

YDU

Flood Seal, YY Type NonFused Disconnect StreetLight Kit, #14-#4 Copper, #14-#2 Aluminum, includes Insulating Twin Cap and Twin Rocket, Fuse Clip, Copper Wire 10 Gauge, (3) Screws, Silicone Grease, Oxide Inhibitor, Instruction Sheet

Frequently Asked Questions

Is the SLK 3 A weatherproof?

Yes, the Flood-Seal® rocket provides a watertight seal, making it suitable for outdoor use.

What wire sizes are compatible with the SLK 3 A?

The SLK 3 A is designed for aluminum conductors ranging from #8 AWG to #6 AWG.

How much conductor insulation should be stripped?

Strip approximately 3/4 inch of insulation from the cable end for proper installation.

What voltage rating does the SLK 3 A support?

The SLK 3 A is rated for 600 volts, making it suitable for high-voltage street lighting circuits.

What is the purpose of the silicone grease?

The silicone grease prevents corrosion and aids in installation by reducing friction.

How to Install the SLK-3A Inline Fuse/Disconnect Kit

This guide provides step-by-step instructions for installing the SLK-3A street lighting kit, covering cable preparation, fuse holder assembly, and final connection of the inline fuse/disconnect.

Estimated time: 45m

Tools needed:

Measuring tool (e.g., caliper or ruler), Cutting tool, Wire strippers, Crimping tool (e.g., T&B WT111M or TBM45S with appropriate die)

Supplies needed:

Lubricant, Fuse (13/32" x 1 1/2", 600 Volt 30 Amp max, non-glass body) or connecting link, Assembly dowel

  1. Observe Safety Precautions

    WARNING: Disconnect power before beginning installation to avoid risk of shock. CAUTION: This product must be installed by a qualified electrician in accordance with national and local electrical codes. Identify LINE and LOAD sides of wiring and molded connector bodies before proceeding.

  2. Prepare Load Side Housing

    Measure the cable diameter and refer to Table 1 in the documentation to select the corresponding section on the molded sleeve. Cut off the remaining sections of the load side (plug) housing to the size referenced in the Range column of Table 1.

  3. Prepare Load Side Cable

    Thoroughly clean approximately 8 inches along the load side cable end. Apply lubricant and insert the cable through the small hole in the load side (plug) housing. Push the cable through a sufficient distance to permit 3/8 inch stripping of insulation. Strip the insulation a distance of 3/8 inch from the end.

  4. Crimp Fuse Holder to Load Side Cable

    Insert the prepared load side cable into the crimp barrel of the fuse holder. Crimp the cable securely into the fuse holder. Refer to Table 2 in the documentation for suggested tool and die types based on conductor size.

  5. Secure Fuse Holder in Load Side Housing

    Apply lubricant lightly to the outside of the fuse holder. Place the assembly dowel into the socket of the fuse holder and position the free end of the dowel against a firm surface. Push the load side (plug) housing forward until the fuse holder snaps into its locked position. Wipe off any excess lubricant.

  6. Prepare Line Side Housing and Cable

    Repeat steps 2 through 5 for the line side (receptacle) housing and cable. Ensure the cable diameter is measured, the housing is cut, the cable is cleaned, lubricated, and stripped, the fuse holder is crimped, and then secured into the line side housing using the assembly dowel.

  7. Install Fuse

    Insert a 13/32 inch by 1 1/2 inch fuse (600 Volt 30 Amp maximum) or a connecting link into the plug (load side) housing. WARNING: DO NOT use a glass body fuse.

  8. Connect Housings

    Connect the load side (plug) housing and the line side (receptacle) housing together, ensuring they are firmly joined.

Frequently Asked Questions about ABB - Installation Products

How are Thomas and Betts products typically installed?

Thomas and Betts products are installed using a variety of methods tailored to specific applications, including the use of flexible cords and cable fittings, non-metallic cable glands, and armored cable fittings. Proper selection of fittings is crucial to match the cable type and installation environment, ensuring durability and preventing physical damage. Tools such as the Blackburn® Comfort Crimp® and HEX-FLEX® systems enhance installation efficiency and reliability, reducing labor time and ensuring secure connections.

What accessories are available for Thomas and Betts products?

Thomas and Betts offers a comprehensive range of accessories for their products, including various cord and cable fittings, non-metallic cable glands, service entrance cable fittings, and armored cable fittings. Their accessories are designed to enhance installation efficiency and ensure compatibility with different cable types and environmental conditions, providing reliable connections for a wide array of applications.

What environmental ratings do Thomas and Betts products have?

Thomas and Betts products feature robust environmental ratings, including NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications, as well as IEC 60529 IP66 protection. These ratings ensure that their products are designed to withstand harsh industrial environments, with capabilities to resist dust, water, and corrosion, and operate effectively in a wide temperature range.

What communication protocols do Thomas and Betts products support?

Thomas and Betts products support a wide range of industrial communication protocols, including Ethernet, DeviceNet, PROFIBUS, Modbus, CANopen, and others. This extensive compatibility ensures seamless integration and reliable communication across various industrial automation systems, catering to diverse application needs.

What are the key features of Thomas and Betts products?

Thomas and Betts products are known for their innovative designs, high performance, and compliance with industry standards such as the National Electrical Code and Underwriters' Laboratories. They offer a comprehensive range of rugged and reliable electrical fittings, including liquidtight and dust-tight connections, which enhance installation efficiency and reduce overall project costs. Their products are engineered for durability in harsh environments, ensuring long-term reliability and lower installed costs.

What are the main product lines offered by Thomas and Betts?

Thomas and Betts offers a comprehensive range of product lines including electrical connectors, cable management systems, grounding and bonding solutions, and industrial automation components. Their products are designed for durability and reliability in demanding industrial environments, ensuring optimal performance and safety across various applications.

What technical support does Thomas and Betts offer?

Thomas and Betts offers comprehensive technical support, including access to field application engineers for onsite training and installation assistance. Their technical support staff is available to address inquiries related to product specifications and installation practices, ensuring optimal performance and safety of electrical systems. Additionally, they provide a variety of training programs to enhance the knowledge and skills of users in the field.

What industries and applications are Thomas and Betts products used for?

Thomas and Betts products are utilized across various industries including electrical construction, industrial automation, telecommunications, and utilities. Their extensive range of cord and cable fittings, electrical boxes, and metal framing systems are designed for applications that require durability and reliability in harsh environments, ensuring optimal performance in both permanent and temporary installations.

What certifications and standards do Thomas and Betts products comply with?

Thomas and Betts products comply with critical international certifications including UL (Underwriters Laboratories), CSA (Canadian Standards Association), and CE (European Community). Our products are designed to meet rigorous industrial standards such as NEMA enclosure ratings and IEC 60529 IP ratings, ensuring safety and reliability across various industrial applications.

What are the main product lines offered by Ocal?

Ocal offers a comprehensive range of corrosion-resistant conduit systems, including PVC-coated conduit and fittings, conduit bodies, hazardous location fittings, and strut accessories. Their products are designed to provide superior corrosion protection, featuring a hot-dipped galvanizing process and UL listed Type 4X PVC-coated conduit bodies, ensuring durability in the most demanding environments.