Authorized ABB Distributor (Installation Products)
ABB - Installation Products SLK 60 M - Tin Plated Aluminum Mechanical Streetlight kit, Run #10 - #4 Aluminum and Copper, Tap #10 - #4 Aluminum and Copper. Includes Insulating Cap and Rocket, Wood Dowel, (2) Tin Plated Aluminum Fuse Clips with Screws, Silicone Grease and Instruction Sheet

ABB Installation Products SLK 60 M Tin Plated Aluminum Mechanical Streetlight kit, Run #10 - #4 Aluminum and Copper, Tap…

UPC: 783786752416

Documents & Media
Installation InstructionsManufacturer Product Website

Contact for Pricing

Minimum Qty: 50

Multiplier: 50

*Contact for lower quantities*

Call +1 (262) 252-1600 (toll-free 877-268-3700) or email [email protected] for pricing and availability.

Overview

The ABB SLK 60 M is a mechanical streetlight kit constructed from tin-plated aluminum, designed for reliable electrical connections in outdoor lighting applications. This kit is engineered to accommodate a broad range of conductor sizes, accepting both aluminum and copper wires from #10 AWG to #4 AWG for both run and tap connections. The tin plating on the aluminum components is critical for enhancing conductivity and providing corrosion resistance, essential for exposed outdoor environments. Each SLK 60 M kit includes all necessary components for a secure and watertight installation. The kit contains: * One line-end assembly * One load-end assembly * Two FSS 20 "Flood-Seal"® Rockets * One packet of Silicone Grease * An instruction sheet Note: A fuse is not included. Catalog numbers with the suffix '-60 M' require a 60 Amp fuse. The installation process involves stripping insulation to expose 3/4” of conductor. The line-end housing features cut-off rings to select the correct size for the cable being used. Silicone grease is applied to the cable end and the cut opening of the line-end housing. The line-end cable is inserted until it extends 2” to 3” beyond the housing, and the set screw is torqued to 25 in-lbs. A 13/32” (max. 600 Volt) cartridge fuse is inserted into the load-end assembly (glass body fuses are not to be used). The load-end sealing area is greased. The "Flood-Seal"® Rockets are mated to the line-end assembly for a watertight seal, and the line-end housings are then mated to establish the electrical connection. These instructions apply to both copper and aluminum conductors rated for 600 volts. The ABB SLK 60 M, SKU SLK 60 M, provides a practical and efficient solution for maintaining streetlight infrastructure where flexible conductor sizing and robust environmental protection are required.
  • Tin-plated aluminum construction for corrosion resistance and conductivity.
  • Accommodates #10 AWG to #4 AWG aluminum and copper conductors for run and tap connections.
  • Includes insulating cap, rocket connector, wood dowel, fuse clips with screws, and silicone grease.
  • Designed for outdoor streetlight applications requiring reliable electrical connections.
  • 600 Volt rated for copper and aluminum conductors.

Specifications

Application
Rated 600 Volts, 60 Amps Maximum, perfect for Heavy duty applications
Conductor Range
#10 to #4 AWG
Connection
Mechanical
Finish
Tinned
Insulation
EPDM Rubber
Material
Aluminum
Number of Conductors
2
Special Features
Includes Insulating Rocket and Cap
Type
Breakaway Street Light Kit Non-Fused
Package Dimensions (L x W x H)
0.01 IN x 0.01 IN x 0.01 IN
Package Dimensions (L x W x H)
0.0254 cm x 0.0254 cm x 0.0254 cm
Package Weight (Imperial)
1.0000 L
Package Weight (Metric)
0.4540 kg
600 Amp, 15kV, Deadbreak, ComboT Elbow / Reducing Tap Plug (Universal Aluminum), No Test Point.

655BCETP

600 Amp, 15kV, Deadbreak, ComboT Elbow / Reducing Tap Plug (Universal Aluminum), No Test Point.
Single cable clamp 150-300mm2 for power terminal type 5

45000034

Single cable clamp 150-300mm2 for power terminal type 5
Flood Seal, YY Type Fused Disconnect StreetLight Kit, #14-#4 Copper, #14-#2 Aluminum includes Insulating Twin Cap and Twin Rocket, Fuse Clip, Copper Wire 10 Gauge, (3) Screws, Silicone Grease, Oxide Inhibitor, Instruction Sheet

YFU

Flood Seal, YY Type Fused Disconnect StreetLight Kit, #14-#4 Copper, #14-#2 Aluminum includes Insulating Twin Cap and Twin Rocket, Fuse Clip, Copper Wire 10 Gauge, (3) Screws, Silicone Grease, Oxide Inhibitor, Instruction Sheet
Flood Seal, YY Type NonFused Disconnect StreetLight Kit, #14-#4 Copper, #14-#2 Aluminum, includes Insulating Twin Cap and Twin Rocket, Fuse Clip, Copper Wire 10 Gauge, (3) Screws, Silicone Grease, Oxide Inhibitor, Instruction Sheet

YDU

Flood Seal, YY Type NonFused Disconnect StreetLight Kit, #14-#4 Copper, #14-#2 Aluminum, includes Insulating Twin Cap and Twin Rocket, Fuse Clip, Copper Wire 10 Gauge, (3) Screws, Silicone Grease, Oxide Inhibitor, Instruction Sheet
Aluminum Flood-Seal Mechanical Splice Compression Type Repair Kit, conductor range #2 to 350 kcmil, standard one-hole lugs, connector length 3-15/64 inch. Kit includes (2) Connectors, (2) Caps, (2) Screws, (2) Rockets and 20-1/2 inches of 350 kcmil Aluminum Wire.

URS 125-17 1/2

Aluminum Flood-Seal Mechanical Splice Compression Type Repair Kit, conductor range #2 to 350 kcmil, standard one-hole lugs, connector length 3-15/64 inch. Kit includes (2) Connectors, (2) Caps, (2) Screws, (2) Rockets and 20-1/2 inches of 350 kcmil Aluminum Wire.
Flood Seal, UF Mechanical Splicing Kit, contains EPDM Rubber Insulating Rocket, Cap and Cap Liner, 4 Outlet Connector 1-11/32 x 55/64 x 55/64 inch with Slotted Set Screws and Silicone Grease.

UF 3410

Flood Seal, UF Mechanical Splicing Kit, contains EPDM Rubber Insulating Rocket, Cap and Cap Liner, 4 Outlet Connector 1-11/32 x 55/64 x 55/64 inch with Slotted Set Screws and Silicone Grease.
Mechanical Connector with 4 Outlets Placed inside Plastic Splice Housing, 1-11/32 inch long x 55/64 inch x 55/64 inch.

UF 6055-4

Mechanical Connector with 4 Outlets Placed inside Plastic Splice Housing, 1-11/32 inch long x 55/64 inch x 55/64 inch.
EPDM Sleeve Cover and Cap for UF-A and UF-B Seals, Rocket 5-39/64 inch long x 1-5/8 inch Diameter, Cap 3-39/64 inch long

UF 3410 ROCKET

EPDM Sleeve Cover and Cap for UF-A and UF-B Seals, Rocket 5-39/64 inch long x 1-5/8 inch Diameter, Cap 3-39/64 inch long

How to Install the Flood-Seal SLK 60 M In-Line Fuse/Disconnect Kit

This guide provides step-by-step instructions for safely installing the Flood-Seal SLK 60 M In-Line Fuse/Disconnect Kit for copper and aluminum conductors, including cable preparation and housing assembly.

Estimated time: 30m

Tools needed:

1/8 inch hex wrench, Wooden dowel

Supplies needed:

13/32 inch x 2-1/4 inch (600V max.) fuse (non-glass body), Cable (Copper or Aluminum, #12-4)

  1. Ensure Safety and Identify Wires

    De-energize all associated wires and the working area before beginning installation. Identify the Line and Load side wires and match the corresponding housing body parts. WARNING: Danger of Electric Shock! Installation must be performed by trained installers in accordance with all applicable local, state, and national electrical codes, installation standards, and safety rules.

  2. Prepare Cable Insulation

    Strip 1/2 inch of insulation from the end of the cable, exposing the conductor. Wipe the cable clean and bevel the end of the cable insulation for easier installation into the housing.

  3. Prepare Housing for Cable

    Select the correct cut-off ring on the housing that matches the cable being used. Cut off the end of the housing at the tip of the arrow, ensuring the correct cable size opening is visible.

  4. Apply Grease and Insert Cable

    Apply silicone grease (provided in kit) to the end of the prepared cable and to the cut opening of the housing. Insert the cable into the housing until it extends 2 to 3 inches beyond the housing.

  5. Install Fuse Clip to Conductor

    Install one of the wire end fuse clips onto the exposed conductor using a 1/8 inch hex wrench. Securely tighten the set screw to the conductor. CAUTION: Do not overtighten on smaller size conductors.

  6. Seat Fuse Clip in Housing

    Slide the housing over the fuse clip until resistance is felt. Use the provided wooden dowel to push the fuse clip firmly into its socket until you feel it pop into place.

  7. Apply Grease to Fuse Clip

    Apply a small amount of silicone grease (provided in kit) to the installed fuse clip.

  8. Repeat for Second Cable End

    Complete steps 2 through 7 for the second cable end (either Line or Load, depending on which was done first) and its corresponding housing.

  9. Insert Fuse or Connecting Link

    Insert the specified 13/32 inch x 2-1/4 inch (600V max.) fuse (do not use a glass body fuse) or the connecting link into the Load end housing.

  10. Mate Housings

    Carefully mate the Line end and Load end housings together to establish the electrical connection and complete the assembly of the in-line fuse/disconnect kit.

Frequently Asked Questions about ABB - Installation Products

How are Thomas and Betts products typically installed?

Thomas and Betts products are installed using a variety of methods tailored to specific applications, including the use of flexible cords and cable fittings, non-metallic cable glands, and armored cable fittings. Proper selection of fittings is crucial to match the cable type and installation environment, ensuring durability and preventing physical damage. Tools such as the Blackburn® Comfort Crimp® and HEX-FLEX® systems enhance installation efficiency and reliability, reducing labor time and ensuring secure connections.

What accessories are available for Thomas and Betts products?

Thomas and Betts offers a comprehensive range of accessories for their products, including various cord and cable fittings, non-metallic cable glands, service entrance cable fittings, and armored cable fittings. Their accessories are designed to enhance installation efficiency and ensure compatibility with different cable types and environmental conditions, providing reliable connections for a wide array of applications.

What environmental ratings do Thomas and Betts products have?

Thomas and Betts products feature robust environmental ratings, including NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications, as well as IEC 60529 IP66 protection. These ratings ensure that their products are designed to withstand harsh industrial environments, with capabilities to resist dust, water, and corrosion, and operate effectively in a wide temperature range.

What communication protocols do Thomas and Betts products support?

Thomas and Betts products support a wide range of industrial communication protocols, including Ethernet, DeviceNet, PROFIBUS, Modbus, CANopen, and others. This extensive compatibility ensures seamless integration and reliable communication across various industrial automation systems, catering to diverse application needs.

What are the key features of Thomas and Betts products?

Thomas and Betts products are known for their innovative designs, high performance, and compliance with industry standards such as the National Electrical Code and Underwriters' Laboratories. They offer a comprehensive range of rugged and reliable electrical fittings, including liquidtight and dust-tight connections, which enhance installation efficiency and reduce overall project costs. Their products are engineered for durability in harsh environments, ensuring long-term reliability and lower installed costs.

What are the main product lines offered by Thomas and Betts?

Thomas and Betts offers a comprehensive range of product lines including electrical connectors, cable management systems, grounding and bonding solutions, and industrial automation components. Their products are designed for durability and reliability in demanding industrial environments, ensuring optimal performance and safety across various applications.

What technical support does Thomas and Betts offer?

Thomas and Betts offers comprehensive technical support, including access to field application engineers for onsite training and installation assistance. Their technical support staff is available to address inquiries related to product specifications and installation practices, ensuring optimal performance and safety of electrical systems. Additionally, they provide a variety of training programs to enhance the knowledge and skills of users in the field.

What industries and applications are Thomas and Betts products used for?

Thomas and Betts products are utilized across various industries including electrical construction, industrial automation, telecommunications, and utilities. Their extensive range of cord and cable fittings, electrical boxes, and metal framing systems are designed for applications that require durability and reliability in harsh environments, ensuring optimal performance in both permanent and temporary installations.

What certifications and standards do Thomas and Betts products comply with?

Thomas and Betts products comply with critical international certifications including UL (Underwriters Laboratories), CSA (Canadian Standards Association), and CE (European Community). Our products are designed to meet rigorous industrial standards such as NEMA enclosure ratings and IEC 60529 IP ratings, ensuring safety and reliability across various industrial applications.

What are the main product lines offered by Ocal?

Ocal offers a comprehensive range of corrosion-resistant conduit systems, including PVC-coated conduit and fittings, conduit bodies, hazardous location fittings, and strut accessories. Their products are designed to provide superior corrosion protection, featuring a hot-dipped galvanizing process and UL listed Type 4X PVC-coated conduit bodies, ensuring durability in the most demanding environments.