Authorized ABB Distributor (Installation Products)
ABB - Installation Products FYA 4 - Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 4, aluminum run copper tap fused, installing dies 52,BG,243,5/8

ABB Installation Products FYA 4 Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with…

UPC: 783786727513


Documents & Media
Installation InstructionsManufacturer Product Website

Contact for Pricing

Call +1 (262) 252-1600 (toll-free 877-268-3700) or email [email protected] for pricing and availability.

Overview

The ABB FYA 4 Flood-Seal Y-Type Fuse & Disconnect Kit is a mechanical fuse and disconnect solution engineered for outdoor street and highway lighting applications. This kit includes a Y-Type insert and housing, load end insert with connector, twin cap, connecting link (disconnect kits only), nut, bolt, Belleville washers, and crimped lug connectors sized for 4 AWG stranded aluminum run copper tap conductors. The Flood-Seal design provides IP-rated protection against moisture and contaminants, making it ideal for coastal, urban, or high-traffic roadway environments where environmental exposure is a concern. Key features include a 600V rating, midget-type fuse compatibility (1 1/2 × 13/32), and tool-free disconnection for quick maintenance and lamp replacement. The kit supports line-side and load-side wiring with #14-6 AWG copper or aluminum conductors on the line end and 4/1/0 AWG on the load end. Installation requires stripping 1/2" of conductor insulation, inserting wires into the connector, and tightening screws to secure them. Silicone grease is applied to the cable end and housing cut opening to ensure proper seating and vibration resistance. The FYA 4 is designed for pole-mounted or luminaire-mounted installations, simplifying maintenance by allowing rapid disconnection without tools. The kit includes installing dies (52, BG, 243, 5/8) for crimped lug terminations, ensuring secure, long-term reliability in harsh outdoor conditions. This solution is part of ABB’s Installation Products line, trusted for industrial and municipal lighting infrastructure.
  • 600V rated mechanical fuse and disconnect kit for outdoor lighting
  • Supports 4 AWG stranded aluminum run copper tap conductors
  • Tool-free disconnection for quick maintenance and lamp replacement
  • Flood-Seal design provides IP-rated protection against moisture and contaminants
  • Includes Y-Type insert, load end connector, twin cap, and crimped lug connectors

Specifications

Amperage Rating
30 A
Application
Rated 600V, 30 Amps Maximum, perfect for heavy-duty applications
Color
Black
Conductor Range
#4 STR AWG
Connection
Compression
Connection Type
Crimped Lug Connectors
Current Rating
4 AWG
Environmental Conditions
WaterTight
Insulation
True
Length
9-3/4 in
Material
Aluminum, Copper
Material
Aluminum
Material
Aluminum and Copper, EPDM-Rubber Housing
Mounting Type
Pole-mounted or Luminaire-mounted
Number of Conductors
3
Series
FYA
Size
4 AWG
Special Features
EPDM Flood-Seal Housing ensures a fully insulated, watertight, and submersible connection. Safe separations to ensure fuse or connecting link stays in load side when separated. Dual-Rated. Approved for a wide range of aluminum or copper connections
Type
Break-Away Streetlight Kits
Voltage Rating
600V
Package Dimensions (L x W x H)
0.01 IN x 0.01 IN x 0.01 IN
Package Dimensions (L x W x H)
0.0254 cm x 0.0254 cm x 0.0254 cm
Package Weight (Imperial)
1.0000 L
Package Weight (Metric)
0.4540 kg
Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 4, copper run, copper tap fused, installing dies 5/16,8,TP,29

FYC 4

Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 4, copper run, copper tap fused, installing dies 5/16,8,TP,29
Single cable clamp 150-300mm2 for power terminal type 5

45000034

Single cable clamp 150-300mm2 for power terminal type 5
Solenoid Valve Connectors, Field Wireable, 3 Pole, Form A 18mm, 250V, 10A, PG11 opening, gray housing

VFN-021-00

Solenoid Valve Connectors, Field Wireable, 3 Pole, Form A 18mm, 250V, 10A, PG11 opening, gray housing
Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 2, aluminum run copper tap fused, installing dies 52,BG,243,5/8

FYA 2

Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 2, aluminum run copper tap fused, installing dies 52,BG,243,5/8
Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 2/0, copper run ,copper tap fused, installing dies 9/16,13,TS,45

FYC 2/0

Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 2/0, copper run ,copper tap fused, installing dies 9/16,13,TS,45
Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 6 ,copper run, copper tap fused, installing dies J,7,TE,24

FYC 6

Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 6 ,copper run, copper tap fused, installing dies J,7,TE,24
Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 1/0, copper run ,copper tap fused, installing dies 1/2,12,TQ,42

FYC 1/0

Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 1/0, copper run ,copper tap fused, installing dies 1/2,12,TQ,42
Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 1 copper run ,copper tap fused, installing dies 3/8,11K,TB,37

FYC 1

Flood-Seal Street and Highway Lighting Mechanical Fuse and Disconnect Kits Y-Type with Crimped Lug Connectors, fused, wire size stranded 1 copper run ,copper tap fused, installing dies 3/8,11K,TB,37

Frequently Asked Questions

What wire size does the FYA 4 support?

The FYA 4 supports stranded 4 AWG wire for the aluminum run and copper tap connections.

Is the FYA 4 suitable for outdoor use?

Yes, the Flood-Seal design provides protection against moisture and contaminants for outdoor applications.

Can the FYA 4 be used for tool-less disconnection?

Yes, the kit is designed for tool-less disconnection, enabling quick maintenance access.

How to Install the FYA/DYA/FYC/DYC Street Lighting Kit

This guide provides step-by-step instructions for the proper assembly and installation of the FYA, DYA (aluminum), FYC, and DYC (copper) street lighting kits. Ensure all safety precautions are followed.

Estimated time: 1h

Tools needed:

Cable diameter measuring tool, Cutting tool, Wire strippers, Crimping tool (refer to Table 2 for specific T&B tools and dies), Wood dowel, Wire brush (for aluminum connections)

Supplies needed:

Lubricant, 13/32" by 1 1/2" fuse (600 Volt 30 Amp max, non-glass body) OR connecting link, Nut, Bolt, 2 Belleville washers, 2 Lugs, HM53 inhibitor or equivalent (for aluminum connections)

  1. Prepare Load Side (Plug) Housing

    WARNING: Disconnect power before installation to avoid risk of shock. CAUTION: This product must be installed by a qualified electrician in accordance with national and local electrical codes. CAUTION: Identify LINE and LOAD sides of wiring and molded connector bodies before beginning installation. Measure the cable diameter and refer to Table 1 to select the corresponding section on the load side (plug) housing. Cut off the remaining sections of the housing to the size referenced in the Range column of Table 1.

  2. Prepare Load Side Cable

    Thoroughly clean approximately 8 inches along the load side cable end. Apply lubricant and insert the cable through the small hole in the load side (plug) housing. Push the cable through a sufficient distance to permit 3/8 inch for stripping of insulation. Strip the insulation a distance of 3/8 inch as shown in the diagram. CAUTION: Do not over strip.

  3. Crimp Fuse Holder to Cable

    Insert the stripped cable into the crimp barrel of the fuse holder. Crimp the connection using the appropriate crimping tool and die, referring to Table 2 for suggested tools and dies based on conductor size.

  4. Secure Fuse Holder in Load Side Housing

    Apply lubricant lightly to the outside of the fuse holder. Place the wood dowel into the socket of the fuse holder and position the free end of the dowel against a firm surface. Push the load side (plug) housing forward until the fuse holder snaps into its locked position. Wipe off any excess lubricant.

  5. Install Fuse or Connecting Link

    Insert a 13/32 inch by 1 1/2 inch fuse (600 Volt 30 Amp max.) or the connecting link into the load side (plug) housing. WARNING: DO NOT use a glass body fuse.

  6. Prepare Y-Type Housing and Run Cable (for run connection)

    Select and cut the correct cut-off ring on the Y-Type housing for the cable being used. Cut and bevel the cable insulation. Apply lubricant to the end of the cable and the cut opening of the housing. Slide the cable through until it extends 2 to 3 inches beyond the housing (Figure A). Strip the insulation to fit the compression lugs (Figure B).

  7. Crimp Lugs and Apply Inhibitor (if aluminum)

    Crimp the lugs with the proper crimping tool, ensuring the pad portions of the lugs are back to back. For aluminum connections only: Wire brush the pads of the lugs, then apply HM53 inhibitor or an equivalent product on the pads. Wipe off any excess inhibitor.

  8. Assemble Line End Insert

    Assemble the line end insert as shown in the illustration, ensuring all components are correctly oriented. Tighten the bolted assembly securely.

  9. Connect Line End Insert to Y-Type Housing

    Apply lubricant as shown in the diagram. Slide the Y-Type housing up to the bottom of the line end insert. Push the line end insert into the opening of the Y-Type housing. While pulling on the cables and holding onto the Y-Type housing, slide the housing toward the line end insert. Push the line end insert until it is fully seated in the housing.

  10. Final Assembly of Load and Line Ends

    Lubricate both the male and female components of the connection points. Insert the load side (plug) housing, with the installed link or fuse clip, into the line end insert until it is fully seated and secure.

Frequently Asked Questions about ABB - Installation Products

How are Thomas and Betts products typically installed?

Thomas and Betts products are installed using a variety of methods tailored to specific applications, including the use of flexible cords and cable fittings, non-metallic cable glands, and armored cable fittings. Proper selection of fittings is crucial to match the cable type and installation environment, ensuring durability and preventing physical damage. Tools such as the Blackburn® Comfort Crimp® and HEX-FLEX® systems enhance installation efficiency and reliability, reducing labor time and ensuring secure connections.

What accessories are available for Thomas and Betts products?

Thomas and Betts offers a comprehensive range of accessories for their products, including various cord and cable fittings, non-metallic cable glands, service entrance cable fittings, and armored cable fittings. Their accessories are designed to enhance installation efficiency and ensure compatibility with different cable types and environmental conditions, providing reliable connections for a wide array of applications.

What environmental ratings do Thomas and Betts products have?

Thomas and Betts products feature robust environmental ratings, including NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications, as well as IEC 60529 IP66 protection. These ratings ensure that their products are designed to withstand harsh industrial environments, with capabilities to resist dust, water, and corrosion, and operate effectively in a wide temperature range.

What communication protocols do Thomas and Betts products support?

Thomas and Betts products support a wide range of industrial communication protocols, including Ethernet, DeviceNet, PROFIBUS, Modbus, CANopen, and others. This extensive compatibility ensures seamless integration and reliable communication across various industrial automation systems, catering to diverse application needs.

What are the key features of Thomas and Betts products?

Thomas and Betts products are known for their innovative designs, high performance, and compliance with industry standards such as the National Electrical Code and Underwriters' Laboratories. They offer a comprehensive range of rugged and reliable electrical fittings, including liquidtight and dust-tight connections, which enhance installation efficiency and reduce overall project costs. Their products are engineered for durability in harsh environments, ensuring long-term reliability and lower installed costs.

What are the main product lines offered by Thomas and Betts?

Thomas and Betts offers a comprehensive range of product lines including electrical connectors, cable management systems, grounding and bonding solutions, and industrial automation components. Their products are designed for durability and reliability in demanding industrial environments, ensuring optimal performance and safety across various applications.

What technical support does Thomas and Betts offer?

Thomas and Betts offers comprehensive technical support, including access to field application engineers for onsite training and installation assistance. Their technical support staff is available to address inquiries related to product specifications and installation practices, ensuring optimal performance and safety of electrical systems. Additionally, they provide a variety of training programs to enhance the knowledge and skills of users in the field.

What industries and applications are Thomas and Betts products used for?

Thomas and Betts products are utilized across various industries including electrical construction, industrial automation, telecommunications, and utilities. Their extensive range of cord and cable fittings, electrical boxes, and metal framing systems are designed for applications that require durability and reliability in harsh environments, ensuring optimal performance in both permanent and temporary installations.

What certifications and standards do Thomas and Betts products comply with?

Thomas and Betts products comply with critical international certifications including UL (Underwriters Laboratories), CSA (Canadian Standards Association), and CE (European Community). Our products are designed to meet rigorous industrial standards such as NEMA enclosure ratings and IEC 60529 IP ratings, ensuring safety and reliability across various industrial applications.

What are the main product lines offered by Ocal?

Ocal offers a comprehensive range of corrosion-resistant conduit systems, including PVC-coated conduit and fittings, conduit bodies, hazardous location fittings, and strut accessories. Their products are designed to provide superior corrosion protection, featuring a hot-dipped galvanizing process and UL listed Type 4X PVC-coated conduit bodies, ensuring durability in the most demanding environments.