ABB Installation Products 262LR-D5230-SG3 15/25kV, 200 Amp, Deadbreak Elbow Connector with Test Point, Cable Insulation Diameter…
UPC: 075114405027
Contact for Pricing
Call +1 (262) 252-1600 (toll-free 877-268-3700) or email [email protected] for pricing and availability.
Overview
- 15/25kV voltage rating with 200A continuous current capacity
- Test point for safe voltage detection without system de-energization
- SG3 cold-shrinkable seal with copper braid and constant force spring for corrosion resistance
- Accommodates cable insulation diameters from 0.890 to 1.220 inches (22.61-30.99mm)
- Includes bi-metal lug for conductor sizes 230 - #1 stranded/compressed or 1/0 solid/compact
Specifications
Amperage Rating | 200 A |
Application | 28 kV, 200 Amp |
Color | Black |
Conductor Range | #1 STR/COMPR AWG , 1/0 SOL/COMPT AWG |
Environmental Conditions | All Weather Conditions |
Insulation | True |
Material | Housing - EPDM-Rubber |
Size | 9.03 inch (299.4 mm) X 8.20 inch (208.3 mm) not including probe, 2.86 inch (72.6 mm) Diameter |
Special Features | 28kV, 200 Amp Loadbreak Elbow. Fully shielded, fully submersible molded rubber housing. 100 percent peroxide-cured construction includes insulation and conductive EPDM materials. Provision for hot stick operation. Provision for ground wire connection. Wide cable range with minimum number of sizes. Long bi-metal compression lug is standard. Non-corrosive capacitive test point |
Standard | ANSI/IEEE Standard 386 |
Temperature Rating, Maximum | 149 F |
Temperature Rating, Maximum | 65 C |
Temperature Rating, Minimum | -40 F |
Temperature Rating, Minimum | -40 C |
Type | Loadbreak Elbow Connector with Test Point |
Voltage Rating | 28 kV |
Package Dimensions (L x W x H) | 0.01 IN x 0.01 IN x 0.01 IN |
Package Dimensions (L x W x H) | 0.0254 cm x 0.0254 cm x 0.0254 cm |
Package Weight (Imperial) | 2.6400 L |
Package Weight (Metric) | 1.1980 kg |
262LR-E5230-SG2
25kV, 200 Amps, Loadbreak Elbow, Cable Insulation Diameter 1.090-1.310 inches, (27.69-33.27 mm), Bi-Metal Conductor, Conductor Size #1 Stranded/Compressed, 1/0 Solid/Compact. With Test Point. 200ECS-G2 Jacket Seal and Grounding Kit Included. Kit Contains Elbow Connector Housing, Compression Lug, Probe, Probe Wrench, Lubricant, Installion Instruction Sheet and Crimp Chart.
375LR-H5250-S
200 Amp, 35kV, Loadbreak Elbow Connector without Test Point, Cable Insulation Diameter 0.850 inch to 1.050 inch. Bi-Metal Compression Lug, Conductor Size AWG 3/0 Compressed/Stranded or 2/0 Solid/Compact. S - Cold-Shrinkable Jacket Seal.
M656CH-DP0596699
600 Amp, 35kV, 4-Way Insulated Bus Bar with Test Point. (1) P0410 - Cable Insulation Diameter P - 1.725 to 1.935 inch, Aluminum Lug for 1000 Stranded/Compressed kcmil. (1) M0330 - Cable Insulation Diameter M - 1.370 to 1.630 inch, Aluminum Lug for 500 Stranded/Compressed kcmil or 600 Solid/Compact kcmil. (2) J0240 - Cable Insulation Diameter J - 0.980 to 1.180 inch, Aluminum Lugs for 1/0 Stranded/Compressed AWG or 2/0 Solid/Compact AWG.
656CETP-H0250
15kV, 600 Series ComboT Elbow with 200 Amp Reducing Tap Plug, Stud, Cable Adapter and Lug Kit, with Test Point. Cable Insulation Diameter Range 0.850 to 1.050 inches, Aluminum Lug, 2/0 Stranded/Compressed or 3/0 Solid/Compact.K655LINK-C-DP0594953
25kV, 600 Amps, Deadbreak Cam-Op Connector Kit. Cable Insulation Diameter LM - 1.280 to 1.630 inch, 700/750 Stranded/Compressed kcmil or 900 Solid/Compact kcmil. Contains (1) Cam-Op Link, (1) Elbow Housing, (1) cable Adapter, (1) Aluminum Compression Lug, (1) Bushing Extender, (2) Retainer Sleeves, (1) Insulated Cap, (1) Mountable Insulated Bushing and (1) Alignment Brackets.M656CH-K0240-S
600 Amp, Separable Cable Joints, Separable H Joint package, 4-Way, with Test point, 35KV, Cable Insulation Diameter 1090 inch to 1.310 inch. Aluminum Compression Lug. Conductor Size AWG Compressed Stranded 1/0 /Solid 2/0 /mmSquared 53.49. 200ECS Jacket Seal Included.
252LR-D5250
15/25kV, 200 Amp, Deadbreak Elbow Connector with Test Point, Cable Insulation Diameter 0.890-1.220 inches (22.61-30.99mm), Bi-Metal Lug, Conductor Size 250 - 2/0 Stranded/Compressed, 3/0 Solid/Compact. Kit Includes Elbow Connector Housing, Lug, Probe, Probe Wrench, Bail Assembly, V.D. Cap-Peroxide, Tube of Lubricant, Crimp Chart and Installations Instructions. 5.454 x 7.531 inches, 2.097 inch diameter.
756LR-N0360-S
35kV, 600 Amps, Deadbreak Elbow with Test Point (with Insulated Plug, Cap, Stud, Lug and Cable Adapter). Aluminum Compression Lug. Cable Insulation Diameter 1.515 inch to 1.780 inch. Conductor Size Compressed/Stranded 650 kcmil or Compacted/Solid 750/800 kcmil. Cold-Shrinkable Jacket Seal Included.Frequently Asked Questions
Is the Elastimold elbow ANSI certified?
Yes, the enhanced Elastimold 200 amp loadbreak elbow has ANSI certification.
What industry standards does the elbow comply with?
The enhanced Elastimold 200 amp loadbreak elbow is IEEE 386 compliant.
What is the operational benefit with Elastimold bushings?
When used with Elastimold bushings, the elbow provides lifetime ease of operation and a non-stick interface.
Does the elbow have a no-stick interface feature?
Yes, it features a no-stick interface when used with Elastimold bushings, which has been NEETRAC tested.
What certifications does the loadbreak elbow have?
It has Rural Utilities Service (RUS) acceptance from the U.S. Department of Agriculture (USDA). It is also IEEE 386 compliant and ANSI certified.
What is the Elastimold 200 amp loadbreak elbow?
It is an enhanced 200 amp loadbreak elbow available for 15 kV and 25 kV series, designed for easier switching.
What is the operational benefit with Elastimold bushings?
When used with Elastimold bushings, the elbow provides lifetime ease of operation and a non-stick interface.
Is the Elastimold elbow ANSI certified?
Yes, the enhanced Elastimold 200 amp loadbreak elbow has ANSI certification.
What industry standards does the elbow comply with?
The enhanced Elastimold 200 amp loadbreak elbow is IEEE 386 compliant.
Does the elbow have a no-stick interface feature?
Yes, it features a no-stick interface when used with Elastimold bushings, which has been NEETRAC tested.
How to Install Elastimold 261LR/262LR Loadbreak Elbow Connectors
This guide provides step-by-step instructions for the safe and proper installation of Elastimold 261LR and 262LR Loadbreak Elbow Connectors, covering initial checks, cable preparation, lug crimping, elbow assembly, grounding, and final connection to a de-energized bushing.
Estimated time: 1h 30m
Tools needed:
Probe Wrench, Crimp Tool, Wire Brush, Wire Strippers, Hotstick
Supplies needed:
Compression Lug, Probe, Lubricant (Do Not Substitute), Copper Ground Wire (No. 14 AWG / 2.5mm or equivalent), Grounding Connector, Cold Shrink Sealing Kit (if applicable)
- Perform Initial Safety and Component Checks
Before starting, ensure all apparatus in the work area are de-energized. This product must be installed only by competent personnel trained in high voltage electrical safety. Inspect all package contents for completeness and damage. Verify all components, including the compression lug and probe, fit properly with the cable and mating products. Check probe threads by hand-threading into the compression lug; replace if resistance is encountered.
- Prepare Cable and Outer Jacket
Train the cable to ensure sufficient slack for operation. Refer to the product manual for specific cable type instructions (e.g., non-jacketed, jacketed concentric neutral, drain wire, copper tape shield) to prepare neutral/grounding wires and remove the outer jacket to the specified length. Cut the cable squarely at the bushing centerline. If using a cold shrink sealing kit, slide the cold shrink tube onto the cable loose end first.
- Prepare Conductor and Crimp Lug
Remove the insulation shield and insulation 2-1/8” (55mm) from the cable end, ensuring a square cut without nicking the conductor. Wire brush bare aluminum conductors and immediately install the compression lug, rotating it to spread inhibitor. Align the lug's threaded hole with the bushing bore and crimp according to the lug's instructions, starting at the crimp line mark and rotating 180 degrees for successive crimps. Carefully wipe excess inhibitor from the lug and cable. Remove the insulation shield as shown in the manual (6-7/8” (175mm) back from the cable end) and bevel the insulation end 1/8” (5mm) maximum. Thoroughly clean the insulation to remove all traces of dirt or excess inhibitor.
- Assemble Elbow Housing and Probe
Lubricate the cable insulation and the inside of the elbow housing with the supplied lubricant; do not substitute. Slide the elbow connector onto the cable with a back-and-forth twisting motion, then wipe off all excess lubricant. Align the elbow with the compression lug’s threaded hole. Thread the probe into the lug by hand, ensuring it turns freely for approximately four turns before becoming snug. Tighten the probe with the supplied wrench until the wrench bends.
- Connect Grounding Wires
Insert one end of a separate copper wire (No. 14 AWG / 2.5mm or equivalent) through the grounding eye on the elbow and twist tightly, taking care not to damage the eye. Twist all neutral wires together and connect them to ground using an appropriate connector, ensuring adequate slack for elbow operation. If using a cold shrink grounding kit, refer to its specific instructions.
- Connect Elbow to De-energized Bushing
CONFIRM THAT THE TRANSFORMER AND ELBOW ARE DE-ENERGIZED before proceeding. Lubricate the receptacle portion of the elbow connector and the mating bushing with the supplied lubricant. Operate the connection using a full insulated 'hotstick' type tool; DO NOT OPERATE BY HAND. Ensure a fast, firm, straight motion to fully engage the elbow and bushing.
Frequently Asked Questions about ABB - Installation Products
How are Thomas and Betts products typically installed?
Thomas and Betts products are installed using a variety of methods tailored to specific applications, including the use of flexible cords and cable fittings, non-metallic cable glands, and armored cable fittings. Proper selection of fittings is crucial to match the cable type and installation environment, ensuring durability and preventing physical damage. Tools such as the Blackburn® Comfort Crimp® and HEX-FLEX® systems enhance installation efficiency and reliability, reducing labor time and ensuring secure connections.
What accessories are available for Thomas and Betts products?
Thomas and Betts offers a comprehensive range of accessories for their products, including various cord and cable fittings, non-metallic cable glands, service entrance cable fittings, and armored cable fittings. Their accessories are designed to enhance installation efficiency and ensure compatibility with different cable types and environmental conditions, providing reliable connections for a wide array of applications.
What environmental ratings do Thomas and Betts products have?
Thomas and Betts products feature robust environmental ratings, including NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications, as well as IEC 60529 IP66 protection. These ratings ensure that their products are designed to withstand harsh industrial environments, with capabilities to resist dust, water, and corrosion, and operate effectively in a wide temperature range.
What communication protocols do Thomas and Betts products support?
Thomas and Betts products support a wide range of industrial communication protocols, including Ethernet, DeviceNet, PROFIBUS, Modbus, CANopen, and others. This extensive compatibility ensures seamless integration and reliable communication across various industrial automation systems, catering to diverse application needs.
What are the key features of Thomas and Betts products?
Thomas and Betts products are known for their innovative designs, high performance, and compliance with industry standards such as the National Electrical Code and Underwriters' Laboratories. They offer a comprehensive range of rugged and reliable electrical fittings, including liquidtight and dust-tight connections, which enhance installation efficiency and reduce overall project costs. Their products are engineered for durability in harsh environments, ensuring long-term reliability and lower installed costs.
What are the main product lines offered by Thomas and Betts?
Thomas and Betts offers a comprehensive range of product lines including electrical connectors, cable management systems, grounding and bonding solutions, and industrial automation components. Their products are designed for durability and reliability in demanding industrial environments, ensuring optimal performance and safety across various applications.
What technical support does Thomas and Betts offer?
Thomas and Betts offers comprehensive technical support, including access to field application engineers for onsite training and installation assistance. Their technical support staff is available to address inquiries related to product specifications and installation practices, ensuring optimal performance and safety of electrical systems. Additionally, they provide a variety of training programs to enhance the knowledge and skills of users in the field.
What industries and applications are Thomas and Betts products used for?
Thomas and Betts products are utilized across various industries including electrical construction, industrial automation, telecommunications, and utilities. Their extensive range of cord and cable fittings, electrical boxes, and metal framing systems are designed for applications that require durability and reliability in harsh environments, ensuring optimal performance in both permanent and temporary installations.
What certifications and standards do Thomas and Betts products comply with?
Thomas and Betts products comply with critical international certifications including UL (Underwriters Laboratories), CSA (Canadian Standards Association), and CE (European Community). Our products are designed to meet rigorous industrial standards such as NEMA enclosure ratings and IEC 60529 IP ratings, ensuring safety and reliability across various industrial applications.
What are the main product lines offered by Ocal?
Ocal offers a comprehensive range of corrosion-resistant conduit systems, including PVC-coated conduit and fittings, conduit bodies, hazardous location fittings, and strut accessories. Their products are designed to provide superior corrosion protection, featuring a hot-dipped galvanizing process and UL listed Type 4X PVC-coated conduit bodies, ensuring durability in the most demanding environments.