ASSY COVER G28 4K, Bulletin MCLP (Non-DPS Service Parts - Other)

Saddle Tie Mount Natural .130" hole 100

Easy-Splice Heat Shrinkable End Cap 750 - 1500 MCM These caps replace greases, tapes, epoxy, encapsulation, or dips. In most sizes, installation may be accomplished in less than one minute. Heat-shrinkable end caps provide for efficient and positive cable end sealing. Made of thermally stabilized polyolefin, the interior of the HSC is coated with a meltable sealant to assure a watertight seal, complete insulation, abrasion and corrosion resistance. Seals may be affected over lead, steel, aluminum, copper and all standard plastic and elastomeric insulating materials and conduit. HSC end sealing caps are qualified to ANSI C119.1-1986 and rated to ICEA electrical withstand test for 1,000 volts. HSC end sealing caps can be used as a live seal for cables carrying up to 1,000 volts. They can also be used as end seals for storing and pulling de-energized cable.

Aluminum conduit bender for 1 Inch EMT or 3/4 Inch Rigid Conduit has an 8 degree inside radius. It has cast in-angle indicators with raised bending points of reference to aid the installer. The body is aluminum die cast which is lightweight yet strong enough for everyday use. FEATURES: INSIDE RADIUS: 8 Degree TYPE: Aluminum Die Cast USE: 1 Inch EMT or 3/4 Inch Rigid Conduit

The Polaris IPLG6-3B Grey Multi-Tap Single Side Entry Connector features 3 ports sized for 6 - 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is specially designed for fine-stranded copper wires with a pre-installed tin plated copper ferule that collapses as the screw is tightened to form a strong connection with fine-stranded wires. Removable access plugs cover the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing fine-stranded wire applications, including installation in cable trays, troughs, wire-ways, raceways, ducts and motor junction boxes.

The Polaris IPLG6-4B Grey Multi-Tap Single Side Entry Connector features 4 ports sized for 6 - 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is specially designed for fine-stranded copper wires with a pre-installed tin plated copper ferule that collapses as the screw is tightened to form a strong connection with fine-stranded wires. Removable access plugs cover the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing fine-stranded wire applications, including installation in cable trays, troughs, wire-ways, raceways, ducts and motor junction boxes.

The Polaris IPLD600-6 Multi-Tap Dual-Sided Entry Connector features 6 ports sized for 600 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Floor Duct 4" Wide X 6' Long White

Vaportite Clear Glass Globe 150 Series - Screw On

Heavy Duty Copper C Tap Grounding Connector for 1/0 to 2/0 AWG APPLICATIONS: Copper "C" Taps are range-taking compression connectors made from high conductivity copper alloy. Ideal for making tap or parallel copper connections from 8 SOL to 4/0 STR conductors. Provides consistent reliability with heavy wall construction that prevents relaxation of the joint after installation. Installation time is reduced because of its "C" shape. UL CU486A, 467 suitable for direct burial and CSA rated Electrical and Grounding.

The Polaris IPL3/0-3B Multi-Tap Single Side Entry Connector features 3 ports sized for 3/0-6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

USB Programmer for BP Series