Non Metallic Splice and Tap Kit 12-14 AWG for 2 Conductors with Ground Non Metallic Splice and Tap Kits are used for tapping into 12 or 14 AWG solid conductor, 2-conductor cable with ground. Approved for use in a variety of applications including: residential branch circuits, manufactured housing and pre-fabricated building structures.

Saddle Tie Mount Natural .130" hole 100

Easy-Splice Heat Shrinkable End Cap 750 - 1500 MCM These caps replace greases, tapes, epoxy, encapsulation, or dips. In most sizes, installation may be accomplished in less than one minute. Heat-shrinkable end caps provide for efficient and positive cable end sealing. Made of thermally stabilized polyolefin, the interior of the HSC is coated with a meltable sealant to assure a watertight seal, complete insulation, abrasion and corrosion resistance. Seals may be affected over lead, steel, aluminum, copper and all standard plastic and elastomeric insulating materials and conduit. HSC end sealing caps are qualified to ANSI C119.1-1986 and rated to ICEA electrical withstand test for 1,000 volts. HSC end sealing caps can be used as a live seal for cables carrying up to 1,000 volts. They can also be used as end seals for storing and pulling de-energized cable.

Aluminum conduit bender for 1 Inch EMT or 3/4 Inch Rigid Conduit has an 8 degree inside radius. It has cast in-angle indicators with raised bending points of reference to aid the installer. The body is aluminum die cast which is lightweight yet strong enough for everyday use. FEATURES: INSIDE RADIUS: 8 Degree TYPE: Aluminum Die Cast USE: 1 Inch EMT or 3/4 Inch Rigid Conduit

The Polaris IPLG6-3B Grey Multi-Tap Single Side Entry Connector features 3 ports sized for 6 - 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is specially designed for fine-stranded copper wires with a pre-installed tin plated copper ferule that collapses as the screw is tightened to form a strong connection with fine-stranded wires. Removable access plugs cover the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing fine-stranded wire applications, including installation in cable trays, troughs, wire-ways, raceways, ducts and motor junction boxes.

Copper Patch Cord, Category 6A Performance, 28AWG, F/UTP, CM/LSZH, Red, 4.5m, 25 pc.

The conversion kit is used to convert an USRC single row end of row frame to UAC to row end of row frame with a 900mm wide aisle pod. It is black.

This Panduit G5 Monitored Switched PDU features (8) C13 outlets. It is a 20 amp, 208 V, single phase PDU with a NEMA L6-20P input plug and a 10 foot (3m) power cord.

OM5, 12 Fiber Interconnect, Plenum, PanMPO Female to PanMPO Female, Method A, Ultra Insertion Loss - 31 Feet

The CD-2001-8-SET Crimp Dies provide circumferential crimp results in terminations with premium electrical and mechanical performance. Color-coded to provide easy matching on connectors while an embossed die index number on the connector barrels provide post crimp inspection. The part number is permanently marked on the crimping die for easy identification and used with the CT-3001/ST and CT-3001/CCP series tools.

OM5, 24 Fiber Trunk, Low Smoke Zero Halogen, PanMPO Female to PanMPO Female, HD Flex Transition, Method B, Ultra Insertion Loss - 36 Meters

Single nail holder to accommodate one 2 nail.