Contact for Pricing
Overview
- Body: Folded and seam welded. Four 8.5 mm diameter holes for wall fixing, pressed out in 20.4 mm diameter × 2 mm depressions, to allow air circulation around the rear part of the enclosure.
- Gland Plate Opening: Situated at the far rear of the enclosure, to make cabling onto the mounting plate easier.
- Protection: Complies with IP 66, TYPE 4, 12, IK 10. For outdoor installation, the use of a rain Hood, ARF, and 100% polyester paint coating plus corrosion protection primer is recommended. Resistance to corrosion must be taken into consideration for outdo
- Mounting plate: The mounting plate is marked vertically at 10 mm intervals, for easy horizontal positioning of equipment. On the top and bottom there are holes to facilitate cable fixing. Fixed onto M8 press welded studs to the rear of the enclosure. All
- Material: Body: 1.2 mm mild steel for enclosures with a depth of 155 mm / 1.4 mm for enclosures with a depth of 210 or 260 mm / 1.5 mm for enclosures with a depth of 300 or 400 mm, or if a height or width is 1000 mm or greater. Gland plate: 1.4 mm mild st
- Lock: nVent HOFFMAN customized double-bit 3 mm lock, with 90° movement and anti-vibration mechanism. Two locks for 600 mm high to 800 mm high enclosures. Espagnolette three point locking for 1000 mm high enclosures and above. Other inserts are available a
- Finish: RAL 7035 structured powder coating.
- Door: Surface mounted with 130° opening. Concealed removable hinges with captive pin. Hinges can be mounted to allow left or right hand opening. Inner M6 welded studs to mount door profiles MMDP, see delivery. Sealing is ensured by an injected one piece p
- Delivery: Enclosure with door and mounting plate (not included for item numbers ending with PER5). For height 600 mm and above, two MMDP door mounting profiles. Gland plate(s) with gasket(s), plastic double-bit 3 mm key, and mounting accessories. Metallic
- Mounting plate: All sides, from 800 mm and above, are strengthened by folded edges
Specifications
Application | Controls and Drives;Factory Automation and Process Control |
Application | Factory Automation and Process Control; Controls and Drives |
Body Thickness | 1.5 mm |
Body Thickness | 16 ga |
Cable Entry | No |
Color | Gray |
Color | Grey |
Color | Light Gray |
Color Code | RAL 7035 |
Construction | Body: 18 gauge Door: 16 gauge |
Cubic Capacity | 3 in3 |
Cubic Capacity | 49161.3 mm3 |
Depth | 210 mm |
Depth | 8.27 in |
Door Thickness | 14 ga |
Door Thickness | 1.5 mm |
Door Thickness | 16 ga |
Finish | Powder Coated |
Gland Plate Opening Depth | 3.78 in |
Gland Plate Opening Width | 16.14 in |
Gland Plate Opening Width | 12.2 in |
Gland Plate Type | 3 |
Height | 700 mm |
Height | 27.56 |
Height | 700 |
Insulation | No |
IP Rating | IP66 |
Latch Quantity | 2 |
Material | Mild Steel |
Material Quality | Mild Steel |
Max Mounting Depth | 7.56 in |
Max Mounting Depth | 11.1 in |
Mounting | Wall Mounted |
Mounting Plate Included | Yes |
Mounting Type | Wall-mount |
NEMA Rating | 12;4 |
NEMA Rating | NEMA Type 4 NEMA Type 12 NEMA Type 13 |
Number of Gland Plate Openings | 1 |
Number Of Outlet | 1 |
Panel Size | 26.38 x 17.72 in |
Panel Size | 72.00 x 72.00 in |
Protection Rating | NEMA Type 4 |
Series | MAS |
Size | 27.56 x 19.69 x 8.27 inch |
Size | 700x500x210mm |
Style | With Mounting Plate |
Type | Mild Steel Wall Mounted Industrial Enclosures |
Weight | 49.64 lb |
Weight | 32 lbs./100ft |
Width | 500 mm |
Width | 19.69 in |
With or Without Panel | With |
Package Dimensions (L x W x H) | 27.93 IN x 20.06 IN x 8.89 IN |
Package Dimensions (L x W x H) | 70.9422 cm x 50.9524 cm x 22.5806 cm |
Package Weight (Imperial) | 49.640 L |
Package Weight (Metric) | 22.517 kg |
BX4
Sealable and transparent protective covers BX4 and non-removable BX4-CA to protect the devices against accidental contact.
LH38
Cord Grip with NPT Threads, Locknut Included, NPT Thread Size 3/8 Inch, Cable Range 0.181 Inch/4.6mm to 0.312 Inch/7.9mm, Hole Clearance 0.670 Inch/17.0mm, Thread Length 0.53 Inch/13.5mm, IP68 Rating, Nylon, Black
LN43DA
1/2 Inch, Straight, One-Piece Liquidtight Non-Metallic Fitting, CSA, UL E32447, Temperatures up to 60 Degrees C, PVC, Grey
LT20D-NEW
1/2 Inch, 90 Degree, Two-Piece Liquidtight Non-Metallic Fitting, UL E32447, Temperatures up to 107 Degrees C, Nitril Rubber O-Ring, PVC, Grey
How to Install the MAS0705021R5 Controller
This guide provides step-by-step instructions for the installation and initial setup of the MAS0705021R5 Controller, ensuring proper mounting, wiring, and configuration.
Estimated time: 45m
Tools needed:
Screwdriver, Wire strippers, Multimeter
Supplies needed:
Mounting screws, Terminal connectors
- Mount the controller
Secure the MAS0705021R5 controller to the DIN rail using the integrated clips. Ensure the controller is level and firmly attached. WARNING: When mounting on or over a combustible surface, install a floor plate of at least 1.43 mm galvanized or 1.6 mm uncoated steel extended at least 150 mm beyond the equipment on all sides.
- Connect the wiring
Use terminal connectors to connect the power supply and input/output wires to the appropriate terminals on the controller. Ensure all connections are secure and insulated to prevent short circuits.
- Verify the installation
Use a multimeter to check the voltage at the power supply terminals to ensure it meets the required specifications. Confirm that all connections are secure and there are no loose wires.
- Configure the controller
Follow the manufacturer's instructions to access the controller's configuration menu. Set the necessary parameters according to your application requirements.
- Calibrate the controller
Perform calibration as per the guidelines provided in the user manual. This may involve adjusting settings based on feedback from connected sensors or devices.
Frequently Asked Questions about nVent
What industries and applications are nVent products used for?
nVent products are engineered for critical infrastructure and industrial applications across multiple demanding sectors. Key markets include Construction, Data Centers, Defense, Healthcare, Mining, Oil & Gas Refineries, Power Plants, Rail/Transit, Renewable Energy, Security, Ship Building, Steel Mills, Telecom, and Utilities. Their solutions are designed to withstand extreme environmental conditions, with temperature ranges from -55°C to 105°C and specialized features like UV resistance, oil resistance, and flame resistance.
What environmental ratings do nVent products have?
nVent enclosures feature comprehensive environmental ratings, including UL 508A, CSA, and NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications. They are rated IEC 60529 IP66, providing robust protection against dust, water, and corrosion in both indoor and outdoor environments. These products operate effectively in temperatures ranging from -40°F to 266°F, with enhanced UV inhibitors for outdoor weathering and oil-resistant gaskets for superior sealing.
What accessories are available for nVent products?
nVent offers a comprehensive range of accessories across multiple product lines, including EMC accessories like bonding cable clamps and strain reliefs, inline accessories such as lock inserts and mounting brackets, CONCEPT accessories including panel conversion kits and rack-mount angles, and seismic accessories for specialized mounting requirements. Key accessory categories include grounding kits, DIN rail mounting solutions, panel supports, handles, and various mounting hardware compatible with different enclosure types.
What certifications and standards do nVent products comply with?
nVent products meet critical international certifications including UL (United States), CSA (Canada), CE (European Community), and EAC (Russia). Our products are designed to comply with rigorous industrial standards such as NEMA enclosure ratings, IEC 60529 IP ratings, and international safety standards across multiple industrial markets including oil & gas, power, manufacturing, and infrastructure.
What is nVent's warranty policy?
nVent offers a standard 18-month warranty from invoicing date for most automation products, covering defects in workmanship and materials. The warranty requires proper transportation, handling, storage, and installation within specified environmental conditions. Warranty coverage includes repair or replacement at nVent's discretion, with certain conditions such as authorized service repairs and operation within designed capacity limits.
What technical support does nVent offer?
nVent offers comprehensive technical support through multiple global contact centers across North America, South America, Europe, Middle East, India, and Asia. Customers can reach technical experts by phone at regional numbers, with the North American headquarters in Minneapolis, MN providing primary support at +1.763.421.2240. Additionally, nVent provides online support resources through their website, including CAD drawing downloads and an 'Ask The Expert' feature to assist with product technical inquiries.