POLARIS 750 Multi-Tap Black Insulated Connector with 4 Conductors and One Side Wire Entry. Rated for 750-250 MCM, 90 degree C and 600V.

NSI's NO/NC SPDT Magnetic Reed Switch is a Single-Pole, Double-Throw switch. It draws no power while in the closed position, but when the magnet is applied, the common reed swings from the normally closed state to the normally open contact. When the magnet is removed, the reed contact moves back to the normally closed contact.

Red Press In Indicator Light - White Bezel High quality indicator lights are made of nylon with polycarbonate lens material and neon lamps. 125-Volt rated. Connection with 6 inch wire leads.

Amber Press In Indicator Light Stainless Bezel High quality indicator lights are made of nylon with polycarbonate lens material and neon lamps. 125-Volt rated. Connection with 6 inch wire leads.

The Polaris ISR-250 Multi-Tap In-Line Entry Connector features 2 ports sized for 250 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Non Metallic Splice and Tap Kit 12-14 AWG for 2 Conductors with Ground Non Metallic Splice and Tap Kits are used for tapping into 12 or 14 AWG solid conductor, 2-conductor cable with ground. Approved for use in a variety of applications including: residential branch circuits, manufactured housing and pre-fabricated building structures.

Tefzel Cable Ties, 7.50", 50Lb Min Min. Tensile STRength, UL 94V-O Approved, Plenum Rated, 100

Easy-Splice Direct Burial Roll-On Splice Sleeve for 8 to 2/0 AWG is an easy "roll-on" way to insulate and seal cable connections up to 1,000 volts. Each kit includes one Easy-Splice sleeve and sealant strips. For use on standard poly or elastomeric-insulated cables. Insulates and seals in-line compression connectors or terminal lugs. Cable can be energized immediately.

Easy-Splice Direct Burial Roll-On Splice Sleeve for 250 - 600 MCM Easy "roll-on" way to insulate and seal cable connections up to 1,000 volts. The gripping force of the EPDM elastomer combines with high performance sealant to form a water resistant, UV resistant insulating sleeve appropriate for direct burial application over in-line compression connectors. Ideal for use where gas or electric heating devices are not approved. RUS accepted as a secondary tap or splice cover. Each kit includes one Easy-Splice sleeve and sealant strips. Qualified to ANSI C119.1-1986. CSA certified to C22.2 No. 198.2. UL 486D listed, suitable for direct burial. APPLICATION: For use on standard poly or elastomeric-insulated cables. Insulates and seals in-line compression connectors or terminal lugs. Cable can be energized immediately.

Saddle Tie Mount Natural .130" hole 100

Saddle Tie Mount Black .120" hole 100

Easy-Splice Heat Shrinkable End Cap 750 - 1500 MCM These caps replace greases, tapes, epoxy, encapsulation, or dips. In most sizes, installation may be accomplished in less than one minute. Heat-shrinkable end caps provide for efficient and positive cable end sealing. Made of thermally stabilized polyolefin, the interior of the HSC is coated with a meltable sealant to assure a watertight seal, complete insulation, abrasion and corrosion resistance. Seals may be affected over lead, steel, aluminum, copper and all standard plastic and elastomeric insulating materials and conduit. HSC end sealing caps are qualified to ANSI C119.1-1986 and rated to ICEA electrical withstand test for 1,000 volts. HSC end sealing caps can be used as a live seal for cables carrying up to 1,000 volts. They can also be used as end seals for storing and pulling de-energized cable.