Showing 781-792 of 934 results

Panduit
FR6TB12M
Used to support the 6x4 and 4x4 systems by spanning two threaded rod drops. Can be installed from above or below. Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamp enables fast assembly to channel. Use 7/16in nut driver on slide clamps, For 12mm threaded rod.
Contact for Pricing
Minimum Qty: 20
Multiplier: 1
*Contact for lower quantities*

Panduit
F2PCLB58
The fiber mounting 2-piece ladder rack bracket attaches to either a 3/8" (9.5mm) wide x 1 1/2" (38.1mm) or a 3/8" (9.5mm) wide x 2" (50.8mm) ladder rack rail. The bracket halves slide into position and clamp together on the ladder rack rail, which allows for one-handed assembly of the 5/8" threaded rod (not included). It contains the bracket and hardware for attaching the bracket to the ladder rack. It is black and made of steel.
Contact for Pricing
Minimum Qty: 10
Multiplier: 1
*Contact for lower quantities*

Panduit
F2PCLB12
Two-piece bracket attaches to 3/8" (9.5mm) wide x 1 1/2" (38.1mm) or 3/8" (9.5mm) wide x 2" (50.8mm) ladder rack rail. Bracket halves slide into position and clamp together on the ladder rack rail, which allows for a one-handed assembly of the threaded rod (not included). Contains bracket and hardware for attaching bracket to ladder rack.
Contact for Pricing
Minimum Qty: 10
Multiplier: 1
*Contact for lower quantities*

Panduit
FRIVRA4X4BL
Attaches to 4x4 channel and/or fittings to create a 90 upward angle from a straight horizontal run. Used with outside vertical 90 angle fitting FROVRA4X4BL to change level of a straight horizontal run. Includes split cover.
Contact for Pricing

Panduit
FRRF2412YL
The fitting attaches any 24x4 FiberRunner Fitting or Channel to any 12x4 FiberRunner Fitting or Channel. It is yellow and made of ABS plastic. It accepts cover FRRF2412CVYL.
Contact for Pricing

Panduit
FRH4524X4BL
Attaches to 24x4 channel and/or fittings to create a 45 horizontal turn from a straight horizontal run, Black.
Contact for Pricing

Panduit
FRBC6X4BL-E
Pre-assembled 6in x 4in QuikLock coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Black, 20 pieces.
Contact for Pricing
Minimum Qty: 20
Multiplier: 20
*Contact for lower quantities*

Panduit
FRDDSHC6YL
Used to fully enclose the 6x4 dual downspout fitting FRDDS6X4YL. Cover is attached to the fitting base with three hinge clips. The hinge clips allow the hinged cover to rotate to a fully closed position and an open position greater than 90 , Yellow.
Contact for Pricing

Panduit
FEIAB58
Bracket consists of two identical components that clamp onto the crossmembers of standard EIA/TIA racks and are secured with standard hex nuts and split lockwashers (included) tightened onto a length of 5/8" diameter threaded rod (not included). The threaded rod is positioned in the center of the brackets providing a vertical threaded rod stud to mount FiberRunner and Fiber-Duct Threaded Rod Mounting Brackets onto.
Contact for Pricing

Panduit
FR6ACAB
Used to support the 6x4 and 4x4 systems attaching to the top of cabinets. Adjustable from 4 1/4" (108mm) to 9" (229mm) allowing runs to be leveled over uneven cabinet heights. Bracket is secured to the cabinet frame with through bolts (not included). The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps.
Contact for Pricing
Minimum Qty: 6
Multiplier: 1
*Contact for lower quantities*

Panduit
FHDEC2X2OR
Used for closing off open ends of the hinged channel or fittings. No coupler required. Push-on installation, Orange.
Contact for Pricing

Panduit
FHDEC2X2YL
Used for closing off open ends of the hinged channel or fittings. No coupler required. Push-on installation, Yellow.
Contact for Pricing