Contact for Pricing
Overview
- 200 Amp continuous current rating for high-capacity applications
- 15/25kV voltage class with 15.2kV max phase-to-ground operating voltage
- Terminates 4/0 AWG stranded copper conductors for robust current handling
- Fully shielded, fully submersible molded rubber housing for harsh environments
- Non-corrosive, capacitively coupled voltage test point with removable protective cap
Specifications
Application | 15/25 kV, 200 Amps |
Connection | Compression |
Temperature Rating, Maximum | 149 F |
Temperature Rating, Maximum | 65 C |
Temperature Rating, Minimum | -40 F |
Temperature Rating, Minimum | -40 C |
Type | Straight Replacement Contact |
Package Dimensions (L x W x H) | 0.01 IN x 0.01 IN x 0.01 IN |
Package Dimensions (L x W x H) | 0.0254 cm x 0.0254 cm x 0.0254 cm |
Package Weight (Imperial) | 0.1100 L |
Package Weight (Metric) | 0.0500 kg |
171-SV18-18
Pre-assembly with 18 inch vertical mounting bracket, 4 inch pre-galvanized steel square box, box depth-2-1/8 inch, 3/4 inch raised two device box cover and pre-installed pigtail.
52171 3/4P
Square Box, 30.3 Cubic Inches, 4 Inch Square x 2-1/8 Inches Deep, 3/4 Inch Knockouts, Pre-Galvanized Steel, Welded Construction, with 10-1/2 Inch #12 AWG Solid Ground Wire Pigtail, For use with Conduit
72151MSP
Square Box, 29.5 Cubic Inches, 4-11/16 Inches Square x 1-1/2 Inches Deep, 1/2 Inch and 3/4 Inch Eccentric Knockouts, Pre-Galvanized Steel, Welded Construction, with Metal Stud Bracket and 10-1/2 Inch #12 AWG Solid Wire Pigtail, For use with Conduit
171-SH2346-16
Pre-Fabricated, Single Gang Outlet Box, 30.3 Cubic Inches, 4 Inch Square x 2-1/8 Inch Deep, 1/2 and 3/4 Inch Eccentric Knockouts, 1-1/4 Inch Raised Box Cover, with Grounding #12 AWG Solid Ground Wire Pigtail and Box to Stud Bracket, For Use with Conduit
CXWOWP
Gangable Switch Box, 18 Cubic Inches, 3 Inches Long x 2 Inches Wide x 3-1/2 Inches Deep, 1/2 Inch Knockouts, Pre-Galvanized Steel, Non-Metallic Cable Clamps (C-5), 10-1/2 Inch #12 AWG Solid Pigtail and Ears Flush, For use with Non-Metallic Sheathed CableFrequently Asked Questions
What conductor sizes does the 151-SRC-40AX support?
The 151-SRC-40AX is designed for 4/0 AWG stranded copper conductors.
What is the maximum operating voltage for this connector?
The maximum phase-to-ground operating voltage is 15.2kV, with a phase-to-phase voltage of 26.3kV.
Is the 151-SRC-40AX suitable for submersible applications?
Yes, the fully shielded, fully submersible molded rubber housing ensures reliable operation in wet or harsh environments.
What voltage test point feature does this connector include?
The connector includes a non-corrosive, capacitively coupled voltage test point with a removable protective cap for safe testing.
What is the impulse withstand rating of the 151-SRC-40AX?
The connector meets a 125kV BIL impulse withstand rating per ANSI/IEEE Standard 386.
What cable insulation diameter range does this connector accommodate?
The connector accommodates cable insulation diameters from 0.575" to 1.220".
What type of cable is the 151-SRC-40AX designed for?
The connector is designed for UD cable with concentric neutral and extruded insulation shielding.
What is the momentary current rating of the 151-SRC-40AX?
The connector has a 10kA symmetrical momentary current rating for 10 cycles.
How to Install the Elastimold 151SR/K151SR Straight Receptacle
This guide provides step-by-step instructions for preparing the cable, assembling the 151SR/K151SR Straight Receptacle, and connecting it to a mating plug or apparatus, ensuring proper grounding and safety.
Estimated time: 1h
Tools needed:
Wire strippers, Cable cutting tool, Wire brush, Crimping tool, Rag, Approved solvent
Supplies needed:
151SR/K151SR Straight Receptacle kit, Conductor Contact, Nylon Venting Rod, Lubricant, Crimp Chart, Solid dielectric type cable, Silicone grease, #14 AWG copper wire (or equivalent), Elastimold bail, Insulating plug (K150DP) (optional)
- De-energize Apparatus and Review Safety
DANGER: Ensure all apparatus is de-energized during installation or removal of parts. Read all safety warnings and follow individual user, local, and national work rules. Inspect all parts for damage, rating, and compatibility with mating parts before proceeding. This product should only be installed by competent personnel trained in high voltage electrical equipment safety practices.
- Prepare Cable Jacket
Cut and remove the cable jacket. For jacketed concentric neutral cable, remove 8 inches from the cable end, allowing sufficient concentric neutral wires for grounding. For copper tape shield cable, remove 7 1/2 inches of jacket and 6 1/2 inches of copper tape shield from the cable end. If using an ECS or MA grounding device, follow its specific jacket cut-back instructions.
- Prepare Cable Insulation and Conductor
Remove 7/8 to 1 inch (or 1 3/4 to 1 7/8 inches for #1 stranded/compressed and #1/0 compressed/solid aluminum cable) of cable insulation and conductive shield. Cut squarely; do not pencil the conductor end. Wire brush bare aluminum conductors and immediately insert them into the crimp barrel, which contains an inhibitor.
- Crimp Conductor Contact
Crimp the socket terminal onto the bared conductor, ensuring the conductor remains fully seated in the connector. Refer to the crimp chart packed with the contact. Start crimps at the imprinted crimp line and rotate each successive crimp or indent 90 degrees. If using aluminum cable, carefully wipe any excess inhibitor from the contact and cable insulation.
- Prepare Semi-Conductive Shield and Clean Insulation
Remove the semi-conductive shield to a point 7 9/16 to 7 5/8 inches back from the end of the pin with a straight, smooth, 'squared' cut. DO NOT CUT OR NICK THE INSULATION. Pencil the insulation 1/8 inch. Clean the outer jacket and thoroughly clean the insulation to remove all traces of semi-conducting residue by wiping with a rag wet with an approved solvent, always wiping from the end of the cable toward the outer jacket. If using an ECS or MA grounding device, install it now following its instructions.
- Lubricate and Assemble Receptacle
Remove the protective cap from the straight receptacle, keeping the cable insulation and receptacle clean. Apply the supplied lubricant sparingly to the cable as shown in the product diagram and to the inside of the housing. DO NOT SUBSTITUTE other lubricants, as they may be harmful. Push the cable into the housing until the base of the pin chamfer is flush with the inside face of the receptacle. IMPORTANT: If the receptacle is not to be immediately connected, replace the protective cover. The shipping cover offers protection from dirt only and is not an insulating device; obtain an Elastimold insulating plug (K150DP) if an insulating device is required.
- Connect to Mating Plug (Optional)
CAUTION: A bailing arrangement is required when this product is used with any mating Elastimold deadbreak product. Lubricate the nose of the mating plug with silicone grease. Place the nylon rod into the receptacle face until it bottoms (approximately 1 3/4 inches), ensuring the rod is not cut. Insert the plug assembly into the receptacle as far as possible. Pull out the nylon rod. Secure the electrical connection with the aid of an Elastimold bail.
- Ground the Cable
If an ELASTIMOLD grounding device is not being used, connect a length of #14 AWG (or equivalent) copper wire (customer supplied) through the grounding tab and twist tightly as shown in the product diagram. Then, connect the grounding assembly of the connector to the system ground by merging it with the cable shield of each cable. Seal the grounding wires and connections to prevent corrosion.
Frequently Asked Questions about ABB - Installation Products
How are Thomas and Betts products typically installed?
Thomas and Betts products are installed using a variety of methods tailored to specific applications, including the use of flexible cords and cable fittings, non-metallic cable glands, and armored cable fittings. Proper selection of fittings is crucial to match the cable type and installation environment, ensuring durability and preventing physical damage. Tools such as the Blackburn® Comfort Crimp® and HEX-FLEX® systems enhance installation efficiency and reliability, reducing labor time and ensuring secure connections.
What accessories are available for Thomas and Betts products?
Thomas and Betts offers a comprehensive range of accessories for their products, including various cord and cable fittings, non-metallic cable glands, service entrance cable fittings, and armored cable fittings. Their accessories are designed to enhance installation efficiency and ensure compatibility with different cable types and environmental conditions, providing reliable connections for a wide array of applications.
What environmental ratings do Thomas and Betts products have?
Thomas and Betts products feature robust environmental ratings, including NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications, as well as IEC 60529 IP66 protection. These ratings ensure that their products are designed to withstand harsh industrial environments, with capabilities to resist dust, water, and corrosion, and operate effectively in a wide temperature range.
What communication protocols do Thomas and Betts products support?
Thomas and Betts products support a wide range of industrial communication protocols, including Ethernet, DeviceNet, PROFIBUS, Modbus, CANopen, and others. This extensive compatibility ensures seamless integration and reliable communication across various industrial automation systems, catering to diverse application needs.
What are the key features of Thomas and Betts products?
Thomas and Betts products are known for their innovative designs, high performance, and compliance with industry standards such as the National Electrical Code and Underwriters' Laboratories. They offer a comprehensive range of rugged and reliable electrical fittings, including liquidtight and dust-tight connections, which enhance installation efficiency and reduce overall project costs. Their products are engineered for durability in harsh environments, ensuring long-term reliability and lower installed costs.
What are the main product lines offered by Thomas and Betts?
Thomas and Betts offers a comprehensive range of product lines including electrical connectors, cable management systems, grounding and bonding solutions, and industrial automation components. Their products are designed for durability and reliability in demanding industrial environments, ensuring optimal performance and safety across various applications.
What technical support does Thomas and Betts offer?
Thomas and Betts offers comprehensive technical support, including access to field application engineers for onsite training and installation assistance. Their technical support staff is available to address inquiries related to product specifications and installation practices, ensuring optimal performance and safety of electrical systems. Additionally, they provide a variety of training programs to enhance the knowledge and skills of users in the field.
What industries and applications are Thomas and Betts products used for?
Thomas and Betts products are utilized across various industries including electrical construction, industrial automation, telecommunications, and utilities. Their extensive range of cord and cable fittings, electrical boxes, and metal framing systems are designed for applications that require durability and reliability in harsh environments, ensuring optimal performance in both permanent and temporary installations.
What certifications and standards do Thomas and Betts products comply with?
Thomas and Betts products comply with critical international certifications including UL (Underwriters Laboratories), CSA (Canadian Standards Association), and CE (European Community). Our products are designed to meet rigorous industrial standards such as NEMA enclosure ratings and IEC 60529 IP ratings, ensuring safety and reliability across various industrial applications.
What are the main product lines offered by Ocal?
Ocal offers a comprehensive range of corrosion-resistant conduit systems, including PVC-coated conduit and fittings, conduit bodies, hazardous location fittings, and strut accessories. Their products are designed to provide superior corrosion protection, featuring a hot-dipped galvanizing process and UL listed Type 4X PVC-coated conduit bodies, ensuring durability in the most demanding environments.