Hi Temp Male/Female Piggyback Disconnect, 16-14 AWG, 50/Pack

U-Type Die 500Cu

Easy-Splice Heat Shrinkable End Cap These caps replace greases, tapes, epoxy, encapsulation, or dips. In most sizes, installation may be accomplished in less than one minute. Heat-shrinkable end caps provide for efficient and positive cable end sealing. Made of thermally stabilized polyolefin, the interior of the HSC is coated with a meltable sealant to assure a watertight seal, complete insulation, abrasion and corrosion resistance. Seals may be affected over lead, steel, aluminum, copper and all standard plastic and elastomeric insulating materials and conduit. HSC end sealing caps are qualified to ANSI C119.1-1986 and rated to ICEA electrical withstand test for 1,000 volts. HSC end sealing caps can be used as a live seal for cables carrying up to 1,000 volts. They can also be used as end seals for storing and pulling de-energized cable.

Easy-Splice Heat Shrinkable End Cap 6 - 3/0 AWG These caps replace greases, tapes, epoxy, encapsulation, or dips. In most sizes, installation may be accomplished in less than one minute. Heat-shrinkable end caps provide for efficient and positive cable end sealing. Made of thermally stabilized polyolefin, the interior of the HSC is coated with a meltable sealant to assure a watertight seal, complete insulation, abrasion and corrosion resistance. Seals may be affected over lead, steel, aluminum, copper and all standard plastic and elastomeric insulating materials and conduit. HSC end sealing caps are qualified to ANSI C119.1-1986 and rated to ICEA electrical withstand test for 1,000 volts. HSC end sealing caps can be used as a live seal for cables carrying up to 1,000 volts. They can also be used as end seals for storing and pulling de-energized cable.

Easy-Splice Heavy Wall Heat Shrink 6-4/0 AWG, 12 Inch - 3 Count Made of specially formulated polyolefin irradiated and thermally stabilized to give the material "elastic memory". When a proper amount of heat is directly applied to the shrink sleeve, it will permanently shrink to its original unexpanded diameter tightly cover and "mold" itself into irregular shapes. The interior sleeve is coated with an adhesive that assures a watertight seal after shrinking. For use on standard poly- or elastomeric-insulated/ jacketed cables or lead-jacketed cables, which may include aluminum or steel armoring. RUS accepted for use as a secondary tap or splice cover. May be used for jacket repair on cables up to 35 kV. Qualified to ANSI C119.1-1986 for underground splicing. Insulate and seal buried electrical connections rated up to 1,000 volts. UL 486D Listed, CSA C22.2. Temperature Rating: 121-135 degrees C, 1,000V. CONNECTORS UP TO 6 INCHES: Recommended cut length = Connector length + 4 inches. CONNECTORS OVER 6 INCHES: Recommended cut length = Connector length + 5 inches.

Pocket Pal Wire Marker Book with vinyl impregnated cloth nd strong adhesive for lasting labeling. Black legend on white background, 450 wire markers. Legend: A-Z, 0-15, +, -, /

Pocket Pal Wire Marker Book with vinyl impregnated cloth nd strong adhesive for lasting labeling. Black legend on white background, 450 wire markers. Legend: 0-45

U-Type Compression Die - White 300 MCM Copper - 4/0 AWG Aluminum U-Shaped Compression Dies are for use with the NSi-12 Compression Tool and Other Tools. See Cross-Reference Chart below.

22-18 AWG Vinyl Insulated Ring #8 Stud, Bulk

The Polaris ITO-4B Multi-Tap Offset Dual-Side Entry Connector features 2 ports sized for 4 - 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

7 AWG Nylon Insulated Ring 3/8" Stud, Bulk

Standard Cage For Short Term Lighting

NSi Industries Vinyl Insulated 493-Piece Miniterm Kit The NSi Industries Vinyl Insulated 493-Piece Miniterm Kit has been carefully designed to include the most popular NSi miniterm terminals. The cases are made of extremely durable polypropylene. They provide the ultimate in organization and convenience. Miniterms are clearly labeled on the inside lid for easy recognition. Convenient size for easy carrying and easy storing. Refillable and reusable. KIT CONTAINS: Quantity SKU Type Wire Size Stud/Tab Size Length Width 40 R22-6V Vinyl Insulated Ring Terminal 22-18 6 .831 .315 40 R22-10V Vinyl Insulated Ring Terminal 22-18 10 .827 .315 30 R16-6V Vinyl Insulated Ring Terminal 16-14 6 .717 .256 30 R16-10V Vinyl Insulated Ring Terminal 16-14 10 .846 .315 20 R12-8V Vinyl Insulated Ring Terminal 12-10 8 1.063 .374 20 R12-14V Vinyl Insulated Ring Terminal 12-10 1/4 1.201 .472 40 F22-250-3V Vinyl Insulated Female Disconnect 22-18 .250 x.032 - - 35 F16-250-3V Vinyl Insulated Female Disconnect 16-14 .250 x.032 - - 20 F12-250-3V Vinyl Insulated Female Disconnect 12-10 .250 x.032 - - 35 B22-V Vinyl Insulated Butt Connector 22-18 - 1.004 - 25 B16-V Vinyl Insulated Butt Connector 16-14 - 1.004 - 15 B12-V Vinyl Insulated Butt Connector 12-10 - 1.063 - 40 S22-6V Vinyl Insulated Spade Terminal 22-18 6 .896 .224 40 S22-10V Vinyl Insulated Spade Terminal 22-18 10 .906 .378 25 S16-6V Vinyl Insulated Spade Terminal 16-14 6 .839 .252 25 S16-10V Vinyl Insulated Spade Terminal 16-14 10 .846 .315 15 S12-8V Vinyl Insulated Spade Terminal 12-10 8 1.012 .354 12 S12-14V Vinyl Insulated Spade Terminal 12-10 1/4 1.287 .354

Cable Clamp Heavy Duty Black 1" 100

Voltage Marker Card 480 Volts, 12ea. .5x2.25"

Saddle Tie Mount Black .130" hole 100

6 AWG Bare Ring 1/2" Stud - 15 Per Pack

Wire Marker Card (-) vinyl impregnated cloth markers 1.5" long

NSi Duct Tape - 8 mil - 2" x 55 Yards - Single Roll NSi Duct Tape is superior cloth duct tape that is designed to meet all industry demands and applications. Uniform MD/CD tear properties.

The Polaris ITO-4 Multi-Tap Offset Dual-Side Entry Connector features 2 ports sized for 4 - 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Saddle Tie Mount Natural .120" hole 100

8 AWG Vinyl Insulated Ring 1/4" Stud, 250 Per Pack

6 AWG Nylon Insulated Ring 1/4" Stud - 15 Per Pack

Cable Tie Natural ID 7.5" 50lb 100, Natural Cable Ties (zip ties, tie wraps, wire ties) are designed for the bundling of cables and wires.