Showing 1633-1644 of 19,233 results

Panduit
FRFWCSC4LYL
The FiberRunner 4x4 4-Way Cross Cover is for the 4-way cross fitting. The cover creates openings for easy access to add or remove cables.
Contact for Pricing
Minimum Qty: 5
Multiplier: 1
*Contact for lower quantities*

Panduit
FOV452X2LYL
The FiberRunner 2x2 Outside Vertical attaches to a channel to create a 45 downward angle from a straight horizontal run. It is used with inside vertical 45 angle fitting FIV452X2LYL to change the level of straight horizontal runs.
Contact for Pricing

Panduit
FREC24X4LBL
The FiberRunner 24x4 End Cap Fitting is used for closing off open ends of the channel or fittings. The end caps assist in creating a structure that protects fiber optic and high-performance copper data cabling from physical damage.
Contact for Pricing

Panduit
FROVRASC6LYL
The FiberRunner 6x4 Outside Vertical Right-Angle Cover creates openings for easy access to add or remove cables.
Contact for Pricing
Minimum Qty: 5
Multiplier: 1
*Contact for lower quantities*

Panduit
FIVRA2X2LYL
The FiberRunner 2x2 Inside Vertical attaches to a channel to create a 90 upward angle from a straight horizontal run. It is used with outside vertical 90 angle fitting FOVRA2X2LYL to change level of a straight horizontal run.
Contact for Pricing

Panduit
FRH4524X4LYL
The FiberRunner 24x4 Horizontal Fitting attaches to a 24x4 channel and/or fittings to create a 45 horizontal turn from a straight horizontal run.
Contact for Pricing
Minimum Qty: 5
Multiplier: 1
*Contact for lower quantities*

Panduit
FRIDT6X4LYL
The FiberRunner 3-Port Spillout is used with a 6x4 fitting. The spillout is used to route cable into three separate 1.5 inch (3.8mm) diameter split corrugated tubing.
Contact for Pricing
Minimum Qty: 5
Multiplier: 1
*Contact for lower quantities*

Panduit
FRSTRCBL
The Strut Clip Kit allows the FiberRunner Channel or Wyr-Grid Pathway to be attached directly to a standard 1.625 inch W strut structure. The kit contains two clips the hardware for assembly.
Contact for Pricing

Panduit
T70BEI8
The T-70 raceway Base provides solutions for routing low voltage, fiber optic, and/or power cabling along perimeter walls. The T-70 raceway is supplied with pre-punched mounting holes and is tamper resistant. It is 8 ft and Electric Ivory.
Contact for Pricing
Minimum Qty: 48
Multiplier: 48
*Contact for lower quantities*

Panduit
LDPH10EI8-A
The LDPH10 power rated Surface Raceway is a two-piece latching raceway with cover suitable for applications up to 600 V. It features pre-punched mounting holes and factory-applied adhesive backing for fast mounting. It is 8 feet in length and is 1.52 inches wide by 0.86 inches deep. It meets TIA/EIA Standards, is UL5A Listed, and is UL Compliant. It is Electric Ivory.
Contact for Pricing
Minimum Qty: 160
Multiplier: 160
*Contact for lower quantities*

Panduit
LDPH3WH10-A
The LDPH3 power rated Surface Raceway is a two-piece latching raceway with cover suitable for applications up to 600 V. It features pre-punched mounting holes and factory-applied adhesive backing for fast mounting. It is 10 feet in length and is 0.75 inches wide by 0.41 inches deep. It meets TIA/EIA Standards, is UL5A Listed, and is UL Compliant. It is White.
Contact for Pricing
Minimum Qty: 200
Multiplier: 200
*Contact for lower quantities*

Panduit
LDPH10IW8-A
The LDPH10 power rated Surface Raceway is a two-piece latching raceway with cover suitable for applications up to 600 V. It features pre-punched mounting holes and factory-applied adhesive backing for fast mounting. It is 8 feet in length and is 1.52 inches wide by 0.86 inches deep. It meets TIA/EIA Standards, is UL5A Listed, and is UL Compliant. It is Off White.
Contact for Pricing
Minimum Qty: 160
Multiplier: 160
*Contact for lower quantities*