All Categories

Electrical Systems and Lighting and Components and Accessories and Supplies

Electrical Equipment, Components, and Supplies

Electrical Lugs Plugs And Connectors

Subcategories

    Automatic Wire Or Cable Connector

    Backshell connectors

    Battery Terminal

    Cable Gland Connector

    Cable Joint

    Cable Or Wire Lug

    Circular Connectors

    Coaxial Connectors

    Connecting Leads or Wires

    Connector And Cable Seal

    Crab Joint

    Electrical Connector Assembly

    Electrical Extension Cable

    Electrical Metallic Tubing Emt Connectors

    Electrical Metallic Tubing Emt Elbow

    Electrical plug/receptacle adapter

    Electrical Plugs

    Electrical Receptacles

    Electrical Sleeves

    Electrical Taps

    Electrical Terminals

    Electrical Underground Bus Connector

    Electrodes

    Electronic Connector Caps

    Flex Connectors

    Flexible Braid

    Heavy Duty Connector Hood & Housing

    Heavy Duty Connector Insert & Contact

    Input Output Connector Cover

    Jack for Plug

    Jumper Bar

    Liquid Tight Connectors

    Locking Plug

    Mechanical Connector Lug and Cap

    Mechanical Connectors

    Panel Interface Connector

    Power Distribution Blocks

    Printed Circuit Board Pcb Press Fit Header Connector

    Rj Jack And Module

    Tap Off

    Telecommunication Connector

    Terminal Block Accessories

    Terminal Block Covers

    Terminal Block Markers and Marking Accessories

    Terminal Block Separator

    Terminal Blocks

    Terminal Strips

    Twist On Wire Connector

    Wire Connectors

    Wire Or Cable Compression Connector

    Wire Or Cable Compression Reducer

    Wire Or Cable Compression Splice

    Wire Terminal Connector Kit

    Wire Terminal Disconnect

    Wiring Taps

Showing 373-384 of 3,357 results

NSI Industries ISPBS2/0 - The Polaris ISPBS2/0 Multi-Tap Direct Burial Submersible In-Line Port Connector features 2 in-line ports sized for 2/0 - 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of high-dielectric strength rubber insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the radial-tipped set screws. Installs with a hex key and torque wrench, without any tape or additional supplies. Meets or exceeds UL486D and ANSI C119.1 specifications for use in wet or damp locations and designed for use in a wide range of temporary submersal or burial splicing applications.
NSI Industries · Polaris · Polaris EDGE

ISPBS2/0


The Polaris ISPBS2/0 Multi-Tap Direct Burial Submersible In-Line Port Connector features 2 in-line ports sized for 2/0 - 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of high-dielectric strength rubber insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the radial-tipped set screws. Installs with a hex key and torque wrench, without any tape or additional supplies. Meets or exceeds UL486D and ANSI C119.1 specifications for use in wet or damp locations and designed for use in a wide range of temporary submersal or burial splicing applications.

Contact for Pricing

Minimum Qty: 3

Multiplier: 3

*Contact for lower quantities*

NSI Industries IPL500-4C - The Polaris IPL500-4C Multi-Tap Single Side Entry Vision Tap Connector features 4 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

IPL500-4C


The Polaris IPL500-4C Multi-Tap Single Side Entry Vision Tap Connector features 4 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

Minimum Qty: 3

Multiplier: 3

*Contact for lower quantities*

NSI Industries IPLD500-5C - The Polaris IPLD500-5C Multi-Tap Dual-Sided Entry Vision Tap Connector features 5 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

IPLD500-5C


The Polaris IPLD500-5C Multi-Tap Dual-Sided Entry Vision Tap Connector features 5 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

Minimum Qty: 2

Multiplier: 2

*Contact for lower quantities*

NSI Industries ISR-500C - The Polaris ISR-500C Multi-Tap Multi-Tap In-Line Entry Connector features 2 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each in-line port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

ISR-500C


The Polaris ISR-500C Multi-Tap Multi-Tap In-Line Entry Connector features 2 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each in-line port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

Minimum Qty: 2

Multiplier: 2

*Contact for lower quantities*

NSI Industries IPLD500-8C - The Polaris IPLD500-8C Multi-Tap Dual-Sided Entry Vision Tap Connector features 8 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

IPLD500-8C


The Polaris IPLD500-8C Multi-Tap Dual-Sided Entry Vision Tap Connector features 8 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

Minimum Qty: 2

Multiplier: 2

*Contact for lower quantities*

NSI Industries IPLD500-3C - The Polaris IPLD500-3C Multi-Tap Dual-Sided Entry Vision Tap Connector features 3 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

IPLD500-3C


The Polaris IPLD500-3C Multi-Tap Dual-Sided Entry Vision Tap Connector features 3 ports sized for 500 MCM - 4 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

Minimum Qty: 3

Multiplier: 3

*Contact for lower quantities*

NSI Industries 18132C - UB GelFilled Connector 22-26 AWG 100/Clm
NSI Industries · Platinum Tools

18132C


UB GelFilled Connector 22-26 AWG 100/Clm

Contact for Pricing

NSI Industries IPLD250-4CB - The Polaris IPLD250-4CB Multi-Tap Dual-Sided Entry Vision Tap Connector features 4 ports sized for 250 MCM - 6 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

IPLD250-4CB


The Polaris IPLD250-4CB Multi-Tap Dual-Sided Entry Vision Tap Connector features 4 ports sized for 250 MCM - 6 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

NSI Industries IPLD250-3CB - The Polaris IPLD250-3CB Multi-Tap Dual-Sided Entry Vision Tap Connector features 3 ports sized for 250 MCM - 6 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

IPLD250-3CB


The Polaris IPLD250-3CB Multi-Tap Dual-Sided Entry Vision Tap Connector features 3 ports sized for 250 MCM - 6 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

NSI Industries IPLD4-6C - The Polaris IPLD4-6C Multi-Tap Dual-Sided Entry Vision Tap Connector features 6 ports sized for 4 - 14 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

IPLD4-6C


The Polaris IPLD4-6C Multi-Tap Dual-Sided Entry Vision Tap Connector features 6 ports sized for 4 - 14 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

NSI Industries IPL250-3CB - The Polaris IPL250-3CB Multi-Tap Single Side Entry Vision Tap Connector features 3 ports sized for 250 MCM - 6 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

IPL250-3CB


The Polaris IPL250-3CB Multi-Tap Single Side Entry Vision Tap Connector features 3 ports sized for 250 MCM - 6 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

NSI Industries IPL4-4CB - The Polaris IPL4-4CB Multi-Tap Single Side Entry Vision Tap Connector features 4 ports sized for 4 - 14 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries · Polaris · Polaris Vision Tap

IPL4-4CB


The Polaris IPL4-4CB Multi-Tap Single Side Entry Vision Tap Connector features 4 ports sized for 4 - 14 AWG wires. The clear body allows users to see their conductor placement and is wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Contact for Pricing

Showing 373-384 of 3,357 results