Showing 193-204 of 3,038 results

CNN_E fuses are rated for applications up to 80 V dc. As fork lift trucks and electrical vehicle system voltages increase, circuit protection needs to be rated higher than the standard CNN products to handle the increased voltage. The CNN_E is considered very fast-acting for quicker reaction time.
Contact for Pricing
Minimum Qty: 5
Multiplier: 5
*Contact for lower quantities*

CNN_E fuses are rated for applications up to 80 V dc. As fork lift trucks and electrical vehicle system voltages increase, circuit protection needs to be rated higher than the standard CNN products to handle the increased voltage. The CNN_E is considered very fast-acting for quicker reaction time.
Contact for Pricing
Minimum Qty: 5
Multiplier: 5
*Contact for lower quantities*

CNN_E fuses are rated for applications up to 80 V dc. As fork lift trucks and electrical vehicle system voltages increase, circuit protection needs to be rated higher than the standard CNN products to handle the increased voltage. The CNN_E is considered very fast-acting for quicker reaction time.
Contact for Pricing
Minimum Qty: 5
Multiplier: 5
*Contact for lower quantities*

Littelfuse · SPFR Series
SPFRHD4001ST
SPFR 400AMP SINGLE POLE HOLDER / STUDS. The SPFRHD series is specifically designed for 1000 Vdc SPFR fuses ranging up to 400 A in current. It is self-certified to 1000 V and UL Recognized to 600 V.
Contact for Pricing

Littelfuse POWR-PRO® LDC series Class L fuses represent another first in fuse protection. LDC series fuses are the first UL Listed 600 volts AC and DC Class L fuse. Since they may be used for both AC and DC, they eliminate the concern that AC only fuses may be inserted into DC circuits. While LDC series fuses’ UL Listed DC interrupting rating is more than adequate for most applications (50,000 amperes at a 16 millisecond time constant), tests in our high power testing laboratory have shown that this remarkable fuse is capable of performing at much longer time constants. This makes the fuse uniquely suited for such applications as crane rail circuits and mass transit systems. Contact the factory for application information for special needs such as this. For AC-only systems, consider the use of POWR-PRO® KLPC series fuses. They have a full ten seconds time-delay at 500% rated current, and have a wider range of ratings.
Contact for Pricing

JLLS1000 is a Class T fuse with an ampere rating of 1000 and knife-blade-style construction.
Contact for Pricing

Perfect for use in lighting systems, this 300 VAC time delay fuse is designed to handle ballast transformer in-rush currents.
Contact for Pricing
Minimum Qty: 5
Multiplier: 5
*Contact for lower quantities*

IDSR04.5 is a Class RK5 fuse with an ampere rating of 4.5 and cartridge-style construction.
Contact for Pricing
Minimum Qty: 10
Multiplier: 10
*Contact for lower quantities*

IDSR080 is a Class RK5 fuse with an ampere rating of 80 and knife-blade-style construction.
Contact for Pricing
Minimum Qty: 5
Multiplier: 5
*Contact for lower quantities*

FLNR175ID is a Class RK5 fuse with an ampere rating of 175 and knife-blade-style construction.
Contact for Pricing

Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size; for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug).
Contact for Pricing

Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size; for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug).
Contact for Pricing