Showing 1549-1560 of 3,038 results

600 VOLT CABLE LIMITER 350 COPPER 6 TERM. Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size, for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug). Applications: Service entrance conductors, between transformers or network bus and busway terminal boxes, large feeders with three or more conductors per phase. Features: Current-limiting characteristics provide protection to conductor insulation and reduce damage when faults occur. Properly applied cable limiters may permit the use of equipment with reduced withstand ratings. Wide variety of terminations and cable ratings permit use in almost every situation.
Contact for Pricing

600 VOLT CABLE LIMITER 750 COPPER 6 TERM. Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size, for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug). Applications: Service entrance conductors, between transformers or network bus and busway terminal boxes, large feeders with three or more conductors per phase. Features: Current-limiting characteristics provide protection to conductor insulation and reduce damage when faults occur. Properly applied cable limiters may permit the use of equipment with reduced withstand ratings. Wide variety of terminations and cable ratings permit use in almost every situation.
Contact for Pricing

FLNR100ID is a Class RK5 fuse with an ampere rating of 100 and knife-blade-style construction.
Contact for Pricing
Minimum Qty: 5
Multiplier: 5
*Contact for lower quantities*

600 VOLT CABLE LIMITER 500 ALUM 1 TERM. Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size, for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug). Applications: Service entrance conductors, between transformers or network bus and busway terminal boxes, large feeders with three or more conductors per phase. Features: Current-limiting characteristics provide protection to conductor insulation and reduce damage when faults occur. Properly applied cable limiters may permit the use of equipment with reduced withstand ratings. Wide variety of terminations and cable ratings permit use in almost every situation.
Contact for Pricing

600 VOLT CABLE LIMITER 0A3. Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size, for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug). Applications: Service entrance conductors, between transformers or network bus and busway terminal boxes, large feeders with three or more conductors per phase. Features: Current-limiting characteristics provide protection to conductor insulation and reduce damage when faults occur. Properly applied cable limiters may permit the use of equipment with reduced withstand ratings. Wide variety of terminations and cable ratings permit use in almost every situation.
Contact for Pricing

FLSR600ID is a Class RK5 fuse with an ampere rating of 600 and knife-blade-style construction.
Contact for Pricing

FLSR300ID is a Class RK5 fuse with an ampere rating of 300 and knife-blade-style construction.
Contact for Pricing

FLSR03.2ID is a Class RK5 fuse with an ampere rating of 3.2 and cartridge-style construction.
Contact for Pricing
Minimum Qty: 10
Multiplier: 10
*Contact for lower quantities*

FLSR450ID is a Class RK5 fuse with an ampere rating of 450 and knife-blade-style construction.
Contact for Pricing

FLSR.500ID is a Class RK5 fuse with an ampere rating of 0.5 and cartridge-style construction.
Contact for Pricing

FLSR1.12ID is a Class RK5 fuse with an ampere rating of 1.125 and cartridge-style construction.
Contact for Pricing
Minimum Qty: 10
Multiplier: 10
*Contact for lower quantities*

FLSR250ID is a Class RK5 fuse with an ampere rating of 250 and knife-blade-style construction.
Contact for Pricing