The FiberRunner QuikLock Trapeze Bracket is used to support the 12x4 system by spanning two threaded rod drops that are 18 inches apart. It can be installed from above or below. It is used for a 0.5 inch threaded rod. The QuikLock Trapeze Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to the channel.

The Wyr-Grid electro zinc-plated, snap-on sidewall in silver is 6.0" (152 mm) high. It can be attached anywhere along the pathway to retain cables. It comes in standard packages of one.

The Wyr-Grid Snap-On Sidewall Bracket is used in cable routing systems to retain cables and can be attached anywhere along the pathway. The 4 inch snap-on sidewall bracket is 6.9 inches H x 1.2 inches L x 3.71 inches W (175.3mm x 30.5mm x 94.2mm).

The 3-sided vertical tee trumpet spillout fitting is used in cable routing systems to limit the bend radius of the cable to 2 inches (50.8mm) when exiting from a 4x4 or 6x4 FiberRunner Vertical Tee or 4x4 FiberRunner Fitting.

The Rubber Foam Tape is 1/32" X 0.50" X 7YD, for use with Surface Raceway

The FiberRunner QuikLock Existing Threaded Rod Bracket is used to support the 12x4 system from an existing threaded rod installation. It can be secured to a threaded rod with two split nuts. It is used for a 0.625 inch threaded rod. The pre-assembled slide clamps enable fast assembly to the channel.

The Wyr-Grid Pathway Section protects cables between the Main Distribution Area and the Equipment Distribution Area. Unlike other pathways, it installs quickly and can be modified easily, optional sidewalls snap on without extra hardware or tools. Splice connector: WGSPL2430BL, Intersection splice: WGINTSPLBL, Steel, 118.4in x 30.5in x 2.1in (3007mm, 775mm, 53mm), Electro Zinc plated.

The electro zinc-plated vertical wall mount bracket in silver is .33" (8.4 mm) high, 1.5" (38.1 mm) long, and 1.69" (42.9 mm). It comes in standard packages of one.

The FiberRunner 2x2 Spill-Over Junction Fitting is used in cable routing systems. It assembles onto 4x4, 6x4, 12x4, or 24x4 FiberRunner Channels. It mounts directly to the existing installation with no alteration required. The spill-over junction fitting includes mounting hardware.

The black powder coated wall bracket is 2.44" (61.98 mm) high, 6.05" (153.67 mm), long, 3.12" (79.25 mm) wide, and 6.05" (153.67 mm) deep. It is used to support the end of the 18" (457.2 mm), 24" (609.6 mm), or 30" (762 mm) Wyr-Grid Pathway against a wall. The package contains two components that are required to support the wider pathway sections. The mounting hardware for attaching the bracket to the wall is not included. The wall mount bracket comes in standard packages of one.

The Wyr-Grid Hardware Kit is used to quickly and easily bend the straight Wyr-Grid Pathway into a wide-radius 90-degree angle. The 12in (305mm) pathway requires 6 kits, the 18in (457mm) pathway requires 9 kits, the 24in (610mm) pathway requires 12 kits, and the 30in (762mm) pathway requires 15 kits. Black powder coated, 1pc.

FiberRunner QuikLock Threaded Rod Trapeze Bracket for Wyr-Grid 30" (762mm) width. Used to support FiberRunner 4x4, 6x4, 12x4, and 24x4 Channel above or below the Wyr-Grid 30" Pathway using the same 1/2" or 12mm threaded rod used to support the WGTB30BL bracket. Quick mount clips, FRQMC24-X are not included for installing the 24x4 channel. These must be purchased separately. Hardware for attaching to threaded rod sold separately. Available in black powder coat only.