Load Sharer. 120/127V 5A. The T4800 is designed to control a generator operating in parallel with the grid, or a generator operating in parallel with other generators (which are also controlled by T4800 units). The T4800 will continuously measure and compare the active current on the generator to an external DC reference signal connected to the “parallel lines” input. The T4800 will increase or decrease the speed of the generator (through the governor) if it finds the active current level to be either too low or two high. Two built-in relays provide the increase and decrease pulses for a conventional governor. The strength (width) of the pulses is proportional to the frequency/phase deviation. The E7800 Motorised Potentiometer can be used to adapt the contact pulses to a signal suitable for the speed trim input of an electronic speed controller.

EL700 SERIES COMM ADAPTER, Devicenet. Communications Adapter. Optional network-interface and firmware-upgrade communications adapter. Field installs in EL731.

EL731-13-00 is an earth-leakage relay with a supply voltage ac of 24 and a supply voltage dc of 48. Communications is offered via EtherNet-IP™.

G3100 Voltage Relay. 24V DC. The G-Line relays are mainly intended for use in land-based applications. The G-Line relays provide an efficient solution for applications where flexibility and cost of purchase are the main issues. G-Line relays provide high quality, proper measuring techniques and a vast number of programmable options.

Pwr Ref Unit380-450VOutput0-1VDCforT4800. Power Reference Unit. 380-450'V. Output 0-1V DC for T4800.

FlexGen Generator Controller - Basic. Integrated generator controller. The C6200 provides load depending start and stop, automatic synchronization and active / reactive load sharing for one diesel generator (3 phase). The C6200 will also ensure that the generator is always operating at the nominal speed / frequency no matter the load. Advanced grid paralling and Power Factor function are provided as standard. Programmable inputs and outputs allows for easy integration with PLC control. The C6200 can be operated in either fully automatic mode, semi-automatic mode or in manual mode.

Shutdown Unit 24VDC Delay for SPA. The unit has inputs for over speed, low oil pressure and a user defined input which can be used to monitor e.g. high water temperature. The M0600 has an input to indicate that the engine is running and another input to indicate that the engine is in the process of being halted. An output relay will give a closing signal, which can be used to stop the engine via the fuel valve or the stop solonoid (if available). The M0600 will work as a stand-alone protection unit for DIN-rail mounting. Alternatively, when limited space is available, the M0600 can be mounted directly on the rear side of the M2000 Engine Controller.

For splitter applications. Both terminations must be present.

Connects the SE-601 relay to an ungrounded 24 Vdc bus.

The SE-CS30 series is a sensitive nickel-core current transformer used with Littelfuse relays to detect low levels of earth-leakage current.

The SE-CS10 series current transformers (CTs) are key components of the Littelfuse protection relay product line. Littelfuse SE-134C and SE-135 Ground-Fault Ground-Check Monitors are designed specifically for use with the SE-CS10 CTs. A Littelfuse SE-330 Neutral-Grounding-Resistor Monitor and a Littelfuse SE-701 Ground-Fault Monitor can also be equipped with the SE-CS10 series to achieve the desired ground-fault-trip settings. Littelfuse motor- and feeder-protection relays can also make use of the SE-CS10 series either to measure phase current or ground-fault current.

6 Way Transmitter. 24V DC.. The M1500 PT100 6 Way Transmitter includes six current transducers in one box for use with DIN60751 3-wire PT100 temperature sensors. The output signals from the M1500 are 4-20 mA current signals, which can be easily fed into e.g. an analogue alarm monitor such as the M3000 Analogue Alarm Monitor. Each sensor input of the M1500 can be configured for three different temperature ranges: 0-160 ºC, 0-300 ºC or 0-600 ºC.