All Categories

Electrical Systems and Lighting and Components and Accessories and Supplies

Electrical Equipment, Components, and Supplies

Circuit Protection Devices And Accessories

Subcategories

    Automotive Fuse

    Blade Fuses

    Cartridge Fuses

    Ceramic Fuses

    Circuit Breakers

    Circuit Interruptor

    Current Limiter

    Diazed Or Bottle Fuses

    Electronic Fuse

    Fuse Block

    Fuse Clip

    Fuse Holder

    Fuse Parts Or Accessories

    Glass Body Fuses

    Grounding Devices Or Assemblies

    High Speed Fuse

    Lightning Protection Apparatus And Accessories

    Medium Voltage Fuse

    Midget Fuses

    Miniature Circuit Breakers

    Molded Case Circuit Breakers

    Plug Fuses

    Power Fuse

    Semiconductor Fuse

    Surge Arrestor

    Surge Suppressers

    Time Delay Fuses

    Transient Protection Materials

    Vacuum Interruptor

    Voltage Regulator

Showing 5425-5436 of 54,864 results

Littelfuse LECBYC - The Littelfuse 600 V in-line watertight fuse holders are the ideal answer for all high humidity and corrosive environments where fuses are required. Available in both breakaway and non-breakaway, single and double pole versions, these fuse holders allow maximum flexibility for any application.
Littelfuse · LEC Series

LECBYC

0LEC0BYCX


The Littelfuse 600 V in-line watertight fuse holders are the ideal answer for all high humidity and corrosive environments where fuses are required. Available in both breakaway and non-breakaway, single and double pole versions, these fuse holders allow maximum flexibility for any application.

Contact for Pricing

Minimum Qty: 10

Multiplier: 10

*Contact for lower quantities*

Littelfuse LFCL250C3 - Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size; for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug).
Littelfuse · LFCL Series

LFCL250C3

LFCL0250ZC3


Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size; for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug).

Contact for Pricing

Littelfuse LECAJ - The Littelfuse 600 V in-line watertight fuse holders are the ideal answer for all high humidity and corrosive environments where fuses are required. Available in both breakaway and non-breakaway, single and double pole versions, these fuse holders allow maximum flexibility for any application.
Littelfuse · LEC Series

LECAJ

0LEC00AJX


The Littelfuse 600 V in-line watertight fuse holders are the ideal answer for all high humidity and corrosive environments where fuses are required. Available in both breakaway and non-breakaway, single and double pole versions, these fuse holders allow maximum flexibility for any application.

Contact for Pricing

Minimum Qty: 10

Multiplier: 10

*Contact for lower quantities*

Littelfuse LFCL4/0C3 - Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size; for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug).
Littelfuse · LFCL Series

LFCL4/0C3

LFCL04/0ZC3


Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size; for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug).

Contact for Pricing

Littelfuse LFCL350A1 - 600 VOLT CABLE LIMITER 350 ALUM 1 TERM. Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size, for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug). Applications: Service entrance conductors, between transformers or network bus and busway terminal boxes, large feeders with three or more conductors per phase. Features: Current-limiting characteristics provide protection to conductor insulation and reduce damage when faults occur. Properly applied cable limiters may permit the use of equipment with reduced withstand ratings. Wide variety of terminations and cable ratings permit use in almost every situation.
Littelfuse · LFCL Series

LFCL350A1

LFCL0350ZA1


600 VOLT CABLE LIMITER 350 ALUM 1 TERM. Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size, for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug). Applications: Service entrance conductors, between transformers or network bus and busway terminal boxes, large feeders with three or more conductors per phase. Features: Current-limiting characteristics provide protection to conductor insulation and reduce damage when faults occur. Properly applied cable limiters may permit the use of equipment with reduced withstand ratings. Wide variety of terminations and cable ratings permit use in almost every situation.

Contact for Pricing

Littelfuse LFCL750A1 - 600 VOLT CABLE LIMITER 750 ALUM 1 TERM. Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size, for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug). Applications: Service entrance conductors, between transformers or network bus and busway terminal boxes, large feeders with three or more conductors per phase. Features: Current-limiting characteristics provide protection to conductor insulation and reduce damage when faults occur. Properly applied cable limiters may permit the use of equipment with reduced withstand ratings. Wide variety of terminations and cable ratings permit use in almost every situation.
Littelfuse · LFCL Series

LFCL750A1

LFCL0750ZA1


600 VOLT CABLE LIMITER 750 ALUM 1 TERM. Cable limiters are fusible devices that provide very fast short-circuit protection, primarily to faulted cables, but also to other conductors such as busway. Cable limiters do not have an ampere rating, and cannot be used to provide overload protection. Cable limiters are selected by cable size, for example, a 500 kcmil cable requires a 500 kcmil cable limiter. Their main use is to isolate faulted cables in circuits containing three or more parallel conductors per phase. They may be installed on the line side of the main service to provide short-circuit protection to the service conductors. This is especially important when service conductors are tapped from large low-voltage networks or from large low impedance transformers. Cable limiters have terminals which permit them to be installed in a variety of equipment. The most common configuration is the offset blade on one end and the crimp terminal on the other end. This permits the limiter to replace a cable terminal (lug). Applications: Service entrance conductors, between transformers or network bus and busway terminal boxes, large feeders with three or more conductors per phase. Features: Current-limiting characteristics provide protection to conductor insulation and reduce damage when faults occur. Properly applied cable limiters may permit the use of equipment with reduced withstand ratings. Wide variety of terminations and cable ratings permit use in almost every situation.

Contact for Pricing

Littelfuse JTD008ID - JTD008ID is a Class J fuse with an ampere rating of 8 and cartridge-style construction.
Littelfuse · JTD Series

JTD008ID

0JTD008.TXID


JTD008ID is a Class J fuse with an ampere rating of 8 and cartridge-style construction.

Contact for Pricing

Littelfuse JTD.800ID - JTD.800ID is a Class J fuse with an ampere rating of 0.8 and cartridge-style construction.
Littelfuse · JTD Series

JTD.800ID

0JTD.800TXID


JTD.800ID is a Class J fuse with an ampere rating of 0.8 and cartridge-style construction.

Contact for Pricing

Littelfuse JTD015ID - JTD015ID is a Class J fuse with an ampere rating of 15 and cartridge-style construction.
Littelfuse · JTD Series

JTD015ID

0JTD015.TXID


JTD015ID is a Class J fuse with an ampere rating of 15 and cartridge-style construction.

Contact for Pricing

Littelfuse FLSR001ID - FLSR001ID is a Class RK5 fuse with an ampere rating of 1 and cartridge-style construction.
Littelfuse · FLSR Series

FLSR001ID

FLSR001.TXID


FLSR001ID is a Class RK5 fuse with an ampere rating of 1 and cartridge-style construction.

Contact for Pricing

Minimum Qty: 10

Multiplier: 10

*Contact for lower quantities*

Littelfuse FLSR01.4ID - FLSR01.4ID is a Class RK5 fuse with an ampere rating of 1.4 and cartridge-style construction.
Littelfuse · FLSR Series

FLSR01.4ID

FLSR01.4TXID


FLSR01.4ID is a Class RK5 fuse with an ampere rating of 1.4 and cartridge-style construction.

Contact for Pricing

Minimum Qty: 10

Multiplier: 10

*Contact for lower quantities*

Littelfuse JTD050ID - JTD050ID is a Class J fuse with an ampere rating of 50 and cartridge-style construction.
Littelfuse · JTD Series

JTD050ID

0JTD050.TXID


JTD050ID is a Class J fuse with an ampere rating of 50 and cartridge-style construction.

Contact for Pricing

Showing 5425-5436 of 54,864 results