Hammer drive anchors for light-duty fastening in concrete, solid brick, block, or masonry walls. Made of zinc alloy with a zinc plated finish. The anchor size is 1/4 in. x 1-1/2 in., with a 1/4 in. drill size and 1.000 in. minimum embedment depth.

A two-piece hammer drive anchor with a tubular stem and a nail driven through the hollow center of the stem. It is made of zinc alloy with a zinc-plated finish. The anchor measures 1/4 in diameter and 3/4 in length and is designed for attaching termination bar to solid concrete, solid brick, block, or masonry walls.

Hammer drive anchors for light-duty fastening in solid concrete, solid brick, block, or masonry walls. They are made of zinc alloy with a zinc plated finish. This size is 1/4" x 1" with a 1/4" drill size, 0.750" minimum embedment depth, and a mushroom head.

Hammer Drive Anchors for light-duty fastening in concrete, solid brick, block, or masonry walls. They are made of zinc alloy with a zinc plated finish. The anchor size is 1/4 in. x 2 in., with a 1/4 in. drill size, 1.000 in. minimum embedment depth, 0.250 in. diameter, and 0.547 in. head diameter.

One-piece self-drilling wall anchor for use in wallboard. It is made of zinc and installs into drywall or wood studs. The anchor measures 7/16 in diameter and 1.250 in length, with a holding weight of 30 lb.

An injection-molded fluted anchor with protruding ribs that extend from end to end. It is made of engineered plastic and is intended for use with self-tapping or wood screws. The anchor is a light-duty part for use in stone, concrete, hollow block, or brick, with a 1/4" drill size, #10-12 size, 1" length, and 1" minimum embedment depth.

Hollow wall anchors for use with a pre-drilled hole in drywall, sheetrock, plaster, or paneling. They are light-weight duty anchors designed to resist vibration and, when properly installed, will not crack or crumble the wall material. This version is steel with a zinc plated finish and a short combo Phillips/Slotted head with drive point.

An injection-molded plastic anchor with a ribbed shank and longitudinal slits that allow expansion when a screw is inserted. It is designed for use in sheetrock, plaster, brickwork, concrete, tile, and hollow materials. The anchor is yellow dyed and measures 0.750 in long with a 3/16 in drill size.

An injection-molded plastic screw anchor with a flanged opening at the top end and a cone-shaped body cupped at the opposite end. It is a light-duty anchor for use in drywall, concrete, and hollow block or brick. The anchor is made of engineered plastic and measures 7/8 in long with a 3/16 in drill size.

Hollow wall anchor for light-weight duty use in drywall, sheetrock, plaster, or paneling with a pre-drilled hole. It is made of steel with a zinc plated finish. The anchor is 1/4 in. diameter and 2-3/4 in. long, with a 1/2 in. drill size and a 1/4"-20 screw size.

Plastic winged anchors designed for use in sheetrock, plaster, brickwork, concrete, or tile. They are a light-duty plastic anchor with a yellow dyed finish. The anchor size is #12-14-16, with a length of 1.500" and a 5/16" drill size.

Light-weight duty hollow wall anchor for use with a pre-drilled hole in drywall, sheetrock, plaster, or paneling. It is made of zinc-plated steel with a zinc plated finish. The anchor is 1/8 in diameter, 2 in long, and uses a 1/4 in drill size with a 6-32 screw size.