nVent N431246G360 SpectraCool Narrow Advanced Corrosion Protection Lvl 1 RAC, 12000BTU 460V, Lt Gray, Steel
UPC: 783510357870
Documents & Media
Contact for Pricing
Call +1 (262) 252-1600 (toll-free 877-268-3700) or email [email protected] for pricing and availability.
Overview
- Narrow design accommodates 12-inch (300-mm) deep cabinets
- Advanced Corrosion Protection Level 1 (ACP L1) Protection Includes: Protective coatings only applied to copper tubing and coils on the condenser (exterior facing) side as well as thermostat coatings
- Attractive industrial design with minimal use of visible fasteners
- Advanced Corrosion Protection Level 2 (ACP L2) Protection Includes: Everything that was coated in ACP L1, plus protective coatings applied to the evaporator (interior facing) side and an additional wrap around the thermostat
- Cleanable, reusable aluminum mesh filter protects coils for maximum cooling performance
- Outdoor model operating temperature range from -40 F/-40 C to 131 F/55 C (125 F/52 C on N28 Series)
- Reliable mechanical thermostat on enclosure side of the unit; indoor air conditioner models include digital display on ambient side
- Energy efficient rotary compressor on N36 and N43 models
- Dust-resistant condenser coil allows the unit to be run filterless in most applications
- Galvanized sheet-metal cover for rugged factory and outdoor environments
Specifications
Amperage Rating | 3.4;3.6 A;A |
Amperage Rating | 3.4/3.6 A |
Application | Corrosive Environments; Controls and Drives; Power Distribution |
Application | Controls and Drives;Corrosive Environments;Power Distribution |
Btu Rating | 11,000 |
Color | Gray |
Color | Light Gray |
Color Code | RAL 7035 |
Corrosion Resistant | Yes |
Depth | 356 mm |
Depth | 14 in |
Finish | Powder Coated |
Frequency Rating | 50/60 Hz |
Frequency Rating, Maximum | 60 Hz |
Frequency Rating, Minimum | 50 Hz |
Height | 43 in |
Height | 1,092 mm |
Material | Mild Steel |
Max Current | 3.6 A |
Mechanical Advantage | Galvanized sheet metal standard |
NEMA Rating | 4X Watertight, corrosion-resistant |
Nominal Capacity Btu/h | 11,000 Btu/h |
Nominal Capacity Watts | 3,223 W |
Nominal Voltage | 460 V |
Number Of Phases | 3 |
Operating Temperature | -40-125 °F |
Operating Temperature | -40-52 °C |
Operating Temperature | -40-55 °C |
Operating Temperature | -40-55 |
Outdoor Installation | Yes |
Phase | 3 |
Power | 1678/2107 W |
Product Family | SpectraCool |
Protection Rating | NEMA Type 4X |
Refrigerant | R513A |
Remote Access Control | Yes |
Thickness | 1.21 mm |
Thickness | 18 ga |
Thickness | 51.40mm (2.024") |
Type | Air Conditioners |
Voltage AC | 400-460 V |
Voltage Rating | 460 V |
Weight | 138 lb |
Weight | 62.6 kg |
Width | 292 mm |
Width | 11.5 in |
Package Dimensions (L x W x H) | 42.99 IN x 14 IN x 11.5 IN |
Package Dimensions (L x W x H) | 109.1946 cm x 35.56 cm x 29.21 cm |
Package Weight (Imperial) | 138.000 L |
Package Weight (Metric) | 62.597 kg |
N431216G360
SpectraCool Narrow Advanced Corrosion Protection Lvl 1 RAC, 12000BTU 115V, Lt Gray, Steel
N280416G162
The nVent N280416G162 represents a critical component within industrial electrical systems, manufactured by nVent, a globally recognized leader in electrical enclosure and connection solutions. While specific catalog details for this SKU are not provided, its UNSPSC code (40101701) indicates its classification within the 'Electrical components' category, suggesting a role in power distribution, control, or connectivity. Industrial environments demand robust, reliable, and safe electrical components. Products like the nVent N280416G162 are engineered to withstand harsh conditions, including extreme temperatures, moisture, dust, vibration, and corrosive elements. These components are fundamental to the operation of a wide array of industrial machinery and infrastructure, from manufacturing plants and processing facilities to power generation stations and data centers. The integrity of electrical systems hinges on the quality and performance of each individual part, making the selection of trusted manufacturers like nVent paramount. Professionals in electrical engineering, plant maintenance, and system integration rely on components that offer precise functionality and long-term durability. The nVent N280416G162, originating from the United States, benefits from stringent manufacturing standards and quality control processes inherent to domestic production. This ensures that the product meets or exceeds industry specifications for performance and safety. Typical applications for components within this UNSPSC classification include: * **Power Distribution:** Facilitating the safe and efficient flow of electricity to various loads. * **Control Systems:** Enabling the operation and automation of industrial processes. * **Connectivity and Termination:** Providing secure and reliable connections for wiring and cables. * **Protection and Safety:** Contributing to the overall safety of electrical installations by preventing faults and ensuring proper grounding. When specifying components for industrial projects, factors such as voltage ratings, current capacity, environmental protection (IP ratings), material composition, and compliance with relevant standards (e.g., UL, CSA, IEC) are crucial. While specific technical data for the N280416G162 is not detailed here, nVent's reputation is built on delivering solutions that address these critical requirements. Their commitment to innovation and quality ensures that their products contribute to the reliability and longevity of industrial electrical infrastructure. The origin of this component from the US further underscores a commitment to high manufacturing standards and accessibility within North American markets.
How to Install the N431246G360 Air Conditioner
Installation guide for mounting and wiring the N431246G360 SPECTRACOOL Air Conditioner.
Estimated time: 45m
Tools needed:
Screwdriver, Wrench, Ratchet driver
Supplies needed:
Mounting gasket kit, Copper conductors
- Inspect and Test Functionality
Inspect the air conditioner for any damage that may have occurred during shipment. Verify correct functionality before mounting. If the unit has been in a horizontal position, ensure it is placed upright for a minimum of five (5) minutes before operating. Refer to the nameplate for electrical requirements and wire the unit to a properly grounded power supply using copper conductors only. Ensure the minimum circuit ampacity is at least 125% of the amperage shown on the unit nameplate. Immediately after applying power, the evaporator blower should start. Operate the unit with the compressor running for five to ten minutes by setting the cooling thermostat or controller setpoint below the ambient temperature. Condenser air temperatures should become warmer than normal room temperatures within a few minutes after the condenser impellers start.
- Mount the Air Conditioner
Install the provided mounting gasket kit to the air conditioner. Mount the air conditioner onto the enclosure, taking care not to damage the mounting gasket, as it forms the seal between the unit and the enclosure. Avoid dragging the air conditioner on the enclosure with the gasket attached to prevent rips or tears. Start mounting bolts by hand to avoid cross-threading, then tighten with a wrench or ratchet driver.
- Wire the Unit
Refer to the unit's nameplate for specific electrical requirements. Wire the unit to a properly grounded power supply using copper conductors. The electrical circuit should be fused with a slow-blow fuse or a HACR circuit breaker. No other equipment should be connected to this circuit to prevent overloading. If your unit requires a remote-mounted thermostat, wire the thermostat outputs to the appropriate terminals on the 24 VAC terminal strip, following the correct wiring diagram.
- Set Thermostat
Set the thermostat to the required cabinet temperature. Reference the 'Sequence of Operation' on page 4 for details on thermostat adjustment and operation. Note: Do not set the enclosure thermostat to a temperature lower than 70 F, as this can increase the likelihood of frost buildup on the evaporator coil. For testing purposes only, the thermostat stop screw may be removed to allow settings below 70 F, but it must be replaced and verified that the thermostat cannot be set below 70 F after testing.
Frequently Asked Questions about nVent
What industries and applications are nVent products used for?
nVent products are engineered for critical infrastructure and industrial applications across multiple demanding sectors. Key markets include Construction, Data Centers, Defense, Healthcare, Mining, Oil & Gas Refineries, Power Plants, Rail/Transit, Renewable Energy, Security, Ship Building, Steel Mills, Telecom, and Utilities. Their solutions are designed to withstand extreme environmental conditions, with temperature ranges from -55°C to 105°C and specialized features like UV resistance, oil resistance, and flame resistance.
What environmental ratings do nVent products have?
nVent enclosures feature comprehensive environmental ratings, including UL 508A, CSA, and NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications. They are rated IEC 60529 IP66, providing robust protection against dust, water, and corrosion in both indoor and outdoor environments. These products operate effectively in temperatures ranging from -40°F to 266°F, with enhanced UV inhibitors for outdoor weathering and oil-resistant gaskets for superior sealing.
What accessories are available for nVent products?
nVent offers a comprehensive range of accessories across multiple product lines, including EMC accessories like bonding cable clamps and strain reliefs, inline accessories such as lock inserts and mounting brackets, CONCEPT accessories including panel conversion kits and rack-mount angles, and seismic accessories for specialized mounting requirements. Key accessory categories include grounding kits, DIN rail mounting solutions, panel supports, handles, and various mounting hardware compatible with different enclosure types.
What certifications and standards do nVent products comply with?
nVent products meet critical international certifications including UL (United States), CSA (Canada), CE (European Community), and EAC (Russia). Our products are designed to comply with rigorous industrial standards such as NEMA enclosure ratings, IEC 60529 IP ratings, and international safety standards across multiple industrial markets including oil & gas, power, manufacturing, and infrastructure.
What is nVent's warranty policy?
nVent offers a standard 18-month warranty from invoicing date for most automation products, covering defects in workmanship and materials. The warranty requires proper transportation, handling, storage, and installation within specified environmental conditions. Warranty coverage includes repair or replacement at nVent's discretion, with certain conditions such as authorized service repairs and operation within designed capacity limits.
What technical support does nVent offer?
nVent offers comprehensive technical support through multiple global contact centers across North America, South America, Europe, Middle East, India, and Asia. Customers can reach technical experts by phone at regional numbers, with the North American headquarters in Minneapolis, MN providing primary support at +1.763.421.2240. Additionally, nVent provides online support resources through their website, including CAD drawing downloads and an 'Ask The Expert' feature to assist with product technical inquiries.