nVent N280426G360 SpectraCool Narrow Advanced Corrosion Protection Lvl 1 RAC, 4000BTU 230V, Lt Gray, Steel
UPC: 783510357375
Documents & Media
Contact for Pricing
Call +1 (262) 252-1600 (toll-free 877-268-3700) or email [email protected] for pricing and availability.
Overview
- Narrow design accommodates 12-inch (300-mm) deep cabinets
- Advanced Corrosion Protection Level 1 (ACP L1) Protection Includes: Protective coatings only applied to copper tubing and coils on the condenser (exterior facing) side as well as thermostat coatings
- Attractive industrial design with minimal use of visible fasteners
- Advanced Corrosion Protection Level 2 (ACP L2) Protection Includes: Everything that was coated in ACP L1, plus protective coatings applied to the evaporator (interior facing) side and an additional wrap around the thermostat
- Cleanable, reusable aluminum mesh filter protects coils for maximum cooling performance
- Outdoor model operating temperature range from -40 F/-40 C to 131 F/55 C (125 F/52 C on N28 Series)
- Reliable mechanical thermostat on enclosure side of the unit; indoor air conditioner models include digital display on ambient side
- Energy efficient rotary compressor on N36 and N43 models
- Dust-resistant condenser coil allows the unit to be run filterless in most applications
- Galvanized sheet-metal cover for rugged factory and outdoor environments
Specifications
Application | Controls and Drives;Corrosive Environments;Power Distribution |
Application | Power Distribution; Corrosive Environments; Controls and Drives |
Color | Light Gray |
Color | Gray |
Color | Lt Gray |
Color Code | RAL 7035 |
Corrosion Resistant | Yes |
Depth | 356 mm |
Depth | 14 in |
Finish | Powder Coated |
Height | 711 mm |
Height | 28 IN |
Material | Steel |
Material | Mild Steel |
Max Current | 5 A |
Mechanical Advantage | Galvanized sheet metal standard |
Mounting Type | Wall-mounted or panel-integrated |
NEMA Rating | 4X Watertight, corrosion-resistant |
Nema Rating | NEMA 4X |
Nominal Capacity Btu/h | 3,800 Btu/h |
Nominal Capacity Watts | 1,114 W |
Nominal Voltage | 230 V |
Number Of Phases | 1 |
Operating Temperature | -40-125 °F |
Operating Temperature | -40-52 °C |
Operating Temperature | -40-52 |
Outdoor Installation | Yes |
Poles | 1P |
Product Family | SpectraCool |
Protection Rating | NEMA Type 4X |
Refrigerant | R513A |
Remote Access Control | Yes |
Series | SpectraCool Narrow |
Series | SpectraCool Narrow Advanced Corrosion Protection |
Size | Narrow |
Thickness | 1.21 mm |
Thickness | 18 ga |
Thickness | 51.40mm (2.024") |
Type | Air Conditioners |
Voltage AC | 200-250 V |
Voltage Rating | 230 V |
Weight | 38 kg |
Weight | 97 lb |
Width | 292 mm |
Width | 11.5 in |
Package Dimensions (L x W x H) | 28 IN x 14 IN x 11.5 IN |
Package Dimensions (L x W x H) | 71.12 cm x 35.56 cm x 29.21 cm |
Package Weight (Imperial) | 97.000 L |
Package Weight (Metric) | 43.999 kg |
T622226G316P
The nVent T622226G316P is a high-performance industrial electrical connector engineered for reliability in the most demanding environments. Designed and manufactured in the United States, this connector delivers robust performance where moisture, vibration, and temperature extremes are common concerns. Built to meet the rigorous demands of heavy-duty applications, it ensures secure electrical connections in critical infrastructure, machinery, and process control systems. Engineered with nVent’s signature commitment to durability and safety, the T622226G316P features a ruggedized housing that resists corrosion, impact, and environmental contaminants. Its precision-machined contacts provide low-resistance connections, reducing energy loss and minimizing the risk of overheating—even under continuous load. The connector’s compact design allows for easy integration into tight spaces, while its modular construction simplifies installation and maintenance. Whether used in outdoor substations, manufacturing plants, or transportation systems, this connector maintains operational integrity where failure is not an option. Typical applications include power distribution systems, industrial automation, renewable energy installations, and heavy equipment wiring. Professionals in oil and gas, mining, utilities, and marine industries rely on connectors like the T622226G316P to ensure uninterrupted performance in harsh conditions. Installation is straightforward with standard tools, and the connector’s IP-rated sealing provides protection against dust and water ingress, making it ideal for both indoor and outdoor use. nVent, a global leader in electrical and thermal management solutions, brings decades of expertise to every product. The company’s connectors are trusted by engineers and technicians worldwide for their consistency, compliance with industry standards, and long service life. With the T622226G316P, you gain a dependable solution that reduces downtime, enhances safety, and supports the longevity of your electrical systems. For mission-critical connections, choose a connector built to last—choose nVent.
How to Install the N280426G360 Air Conditioner
Installation guide for mounting and wiring the N280426G360 air conditioner. Ensure the unit is properly installed and functional before final mounting.
Estimated time: 45m
Tools needed:
Screwdriver, Wrench, Ratchet driver, Wire strippers, Multimeter
Supplies needed:
Mounting gasket kit, Copper conductors, Slow blow or HACR circuit breaker
- Inspect and test the air conditioner
Inspect the air conditioner for any damage that may have occurred during shipment. Test the unit for functionality before mounting. Ensure the unit has been in an upright position for at least five minutes if it was transported horizontally. Refer to the nameplate for electrical requirements and wire to a properly grounded power supply using copper conductors only. The minimum circuit ampacity should be at least 125% of the amperage shown on the unit nameplate. Immediately after applying power, the evaporator blower should start. Operate the unit with the compressor running for 5-10 minutes by setting the cooling thermostat or controller setpoint below the ambient temperature. Condenser air temperatures should become warmer than room temperatures within a few minutes after the condenser impellers start.
- Prepare for mounting
Install the provided mounting gasket kit to the air conditioner. Ensure the gasket is properly seated to create a watertight seal between the air conditioner and the enclosure.
- Mount the air conditioner
Mount the air conditioner onto the enclosure, taking care not to damage the mounting gasket. Start mounting bolts by hand to avoid cross-threading, then tighten with a wrench or ratchet driver. Ensure the unit remains in an upright position during operation.
- Wire the air conditioner
Refer to the unit's nameplate for specific electrical requirements. Wire the unit to a properly grounded power supply using copper conductors. The electrical circuit should be fused with a slow blow or HACR circuit breaker. If your unit requires a remote-mounted thermostat, wire the thermostat outputs to the appropriate terminals on the 24 VAC terminal strip according to the correct wiring diagram.
- Set the thermostat
Set the thermostat for the required cabinet temperature. Refer to the 'Sequence of Operation' section for details on thermostat adjustment and operation. Do not set the enclosure thermostat to a temperature lower than 70 F, as this can cause coil freeze-ups.
Frequently Asked Questions about nVent
What industries and applications are nVent products used for?
nVent products are engineered for critical infrastructure and industrial applications across multiple demanding sectors. Key markets include Construction, Data Centers, Defense, Healthcare, Mining, Oil & Gas Refineries, Power Plants, Rail/Transit, Renewable Energy, Security, Ship Building, Steel Mills, Telecom, and Utilities. Their solutions are designed to withstand extreme environmental conditions, with temperature ranges from -55°C to 105°C and specialized features like UV resistance, oil resistance, and flame resistance.
What environmental ratings do nVent products have?
nVent enclosures feature comprehensive environmental ratings, including UL 508A, CSA, and NEMA Type 1, 2, 3, 4, 4X, 12, and 13 certifications. They are rated IEC 60529 IP66, providing robust protection against dust, water, and corrosion in both indoor and outdoor environments. These products operate effectively in temperatures ranging from -40°F to 266°F, with enhanced UV inhibitors for outdoor weathering and oil-resistant gaskets for superior sealing.
What accessories are available for nVent products?
nVent offers a comprehensive range of accessories across multiple product lines, including EMC accessories like bonding cable clamps and strain reliefs, inline accessories such as lock inserts and mounting brackets, CONCEPT accessories including panel conversion kits and rack-mount angles, and seismic accessories for specialized mounting requirements. Key accessory categories include grounding kits, DIN rail mounting solutions, panel supports, handles, and various mounting hardware compatible with different enclosure types.
What certifications and standards do nVent products comply with?
nVent products meet critical international certifications including UL (United States), CSA (Canada), CE (European Community), and EAC (Russia). Our products are designed to comply with rigorous industrial standards such as NEMA enclosure ratings, IEC 60529 IP ratings, and international safety standards across multiple industrial markets including oil & gas, power, manufacturing, and infrastructure.
What is nVent's warranty policy?
nVent offers a standard 18-month warranty from invoicing date for most automation products, covering defects in workmanship and materials. The warranty requires proper transportation, handling, storage, and installation within specified environmental conditions. Warranty coverage includes repair or replacement at nVent's discretion, with certain conditions such as authorized service repairs and operation within designed capacity limits.
What technical support does nVent offer?
nVent offers comprehensive technical support through multiple global contact centers across North America, South America, Europe, Middle East, India, and Asia. Customers can reach technical experts by phone at regional numbers, with the North American headquarters in Minneapolis, MN providing primary support at +1.763.421.2240. Additionally, nVent provides online support resources through their website, including CAD drawing downloads and an 'Ask The Expert' feature to assist with product technical inquiries.