NSI Industries IPLD600-12 - The Polaris IPLD600-12 Multi-Tap Dual-Sided Entry Connector features 12 ports sized for 600 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries

IPLD600-12

UPC: 662381789594

Documents & Media
BrochureTechnical Bulletin

Contact for Pricing

Overview

The Polaris IPLD600-12 12-Port Dual-Sided Connector provides the simplest solution for forming a secure connection between up to twelve conductors in applications including cable trays, panel boards, ducts, raceways or troughs. Sized for 600 MCM - 6 AWG wires and rated for 600V, this pre-insulated connector comes pre-loaded with an oxide inhibitor and installs faster than traditional uninsulated connector options using just a hex key and torque wrench. The aluminum alloy body is wrapped in high-dielectric strength plastisol insulation, which is ergonomically molded to offer a comfortable grip, in addition to being resistant to abrasion, chemicals and UV rays. All-in-one design saves time and supplies on each job by eliminating the need for cover and taping; simply brush the conductors clean, strip back their insulation, insert one conductor into each port and secure the covered pressure screws. The IPL600-12 connector is rated for a 90 degrees Celsius operating temperature and dual rated for use with copper and/or aluminum cables, up to max AMP ratings of 2070 and 1620 respectively. Polaris pre-insulated connectors are available in a range of port numbers and configurations to fit the needs of any job, including UL-listed parallel configurations. Polaris: the original pre-insulated connector and still the brand most asked for by name.
  • Dual-Sided Wire Entry: Form secure connections between 12 conductors quickly using the double-side entry ports sized for wires between 600 MCM and 6 AWG
  • Ergonomic Design: Rounded corners and a smooth exterior finish over the abrasion-resistant plastisol insulation make Polaris connectors comfortable to grip
  • Removable Plugs: Each port and set screw comes with a secure plug to prevent debris from entering the insulated connector
  • Pre-filled Oxide Inhibitor: All 12 dual-sided entry (DSE) ports come pre-filled with an oxide inhibitor gel to prevent corrosion and provide low-contact resistance
  • Parallel Rated: This connector is specifically designed and rated for parallel installation, providing a safe and secure way to handle larger projects

Specifications

Aluminum Conductor Max AMP
1620 (based on 8 ports) See Note Amp
Aluminum Conductor Note
Dual Rated for use with copper and or aluminum cables. Not for use with fine-stranded, flexible cables. Parallel Rated to provide safety and NEC compliance when installing parallel runs. No more than 4 input parallel wires.++ For more ampacity -requires installation according to NEMA guidelines - staggering the inputs & outputs & Deratting for more than 3 conductors in a raceway
Application
Wire Termination
Color
Black
Copper Conductor Max
2070 (based on 8 ports) See Note Amp
Environmental Conditions
75 C
Finish
Plastisol Insulated
Material
Aluminum
Number Of Conductors
12
Number Of Poles
1
Size
L=16.250 - W=2.960 - H=3.030 IN
Special Features
(12) 600 MCM-6 AWG - Dual Rated
Standard
UL 486A/B
Temperature Rating
75 C
Type
Double Sided Entry
Voltage Rating
600 V
Warranty
1 Year
Wire Size
600 MCM-6 AWG
Wire Type
Class B & C
Wire/Cable Class
Class B, Class C
Package Dimensions (L x W x H)
16.25 IN x 2.96 IN x 3.03 IN
Package Dimensions (L x W x H)
41.275 cm x 7.5184 cm x 7.6962 cm
Package Weight (Imperial)
4.280 L
Package Weight (Metric)
1.941 kg
The Polaris IT-4 Multi-Tap Single-Side Entry Connector features 2 ports sized for 4 AWG to 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Dual rated for use with copper or aluminum cables. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IT-4

The Polaris IT-4 Multi-Tap Single-Side Entry Connector features 2 ports sized for 4 AWG to 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Dual rated for use with copper or aluminum cables. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IT-250 Multi-Tap Dual-Side Entry Connector features 2 ports sized for 250 MCM to 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Dual rated for use with copper or aluminum cables. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IT-250

The Polaris IT-250 Multi-Tap Dual-Side Entry Connector features 2 ports sized for 250 MCM to 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Dual rated for use with copper or aluminum cables. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IT-4B Multi-Tap Single-Side Entry Connector features 2 ports sized for 4 AWG to 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Dual rated for use with copper or aluminum cables. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IT-4B

The Polaris IT-4B Multi-Tap Single-Side Entry Connector features 2 ports sized for 4 AWG to 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Dual rated for use with copper or aluminum cables. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IT-1/0 Multi-Tap Single-Side Entry Connector features 2 ports sized for 1/0 AWG to 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Dual rated for use with copper or aluminum cables. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IT-1/0

The Polaris IT-1/0 Multi-Tap Single-Side Entry Connector features 2 ports sized for 1/0 AWG to 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Dual rated for use with copper or aluminum cables. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris ISR-250 Multi-Tap In-Line Entry Connector features 2 ports sized for 250 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

ISR-250

The Polaris ISR-250 Multi-Tap In-Line Entry Connector features 2 ports sized for 250 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris ISR-1/0 Multi-Tap In-Line Entry Connector features 2 ports sized for 1/0 - 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

ISR-1/0

The Polaris ISR-1/0 Multi-Tap In-Line Entry Connector features 2 ports sized for 1/0 - 14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPL250-3B Multi-Tap Single Side Entry Connector features 3 ports sized for 250 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPL250-3B

The Polaris IPL250-3B Multi-Tap Single Side Entry Connector features 3 ports sized for 250 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLDS350-12 Multi-Tap Dual-Sided Entry Connector features 12 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. One side features stacked ports, with double-sided ports on the bottom for greater flexibility. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of tight-fitting splicing applications, including installation in small wire ways or panels.

IPLDS350-12

The Polaris IPLDS350-12 Multi-Tap Dual-Sided Entry Connector features 12 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. One side features stacked ports, with double-sided ports on the bottom for greater flexibility. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of tight-fitting splicing applications, including installation in small wire ways or panels.
The Polaris IPLD3/0-8 Multi-Tap Dual-Sided Entry Connector features 8 ports sized for 3/0 - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLD3/0-8

The Polaris IPLD3/0-8 Multi-Tap Dual-Sided Entry Connector features 8 ports sized for 3/0 - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPL4-3B Multi-Tap Single Side Entry Connector features 3 ports sized for 4-14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPL4-3B

The Polaris IPL4-3B Multi-Tap Single Side Entry Connector features 3 ports sized for 4-14 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPL350-6 Multi-Tap Single Side Entry Connector features 6 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPL350-6

The Polaris IPL350-6 Multi-Tap Single Side Entry Connector features 6 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLD250-6 Multi-Tap Dual-Sided Entry Black Connector features 6 ports sized for 250 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLD250-6

The Polaris IPLD250-6 Multi-Tap Dual-Sided Entry Black Connector features 6 ports sized for 250 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Frequently Asked Questions

What is the product code for IPLD600-12?

The product code for IPLD600-12 is BIBD600-12.

What is the operating voltage for IPLD600-12?

The IPLD600-12 operates at 12V.

What is the maximum current rating for IPLD600-12?

The maximum current rating for IPLD600-12 is 500A.

What are the installation requirements for IPLD600-12?

Installation should follow standard electrical practices and local codes.

What safety precautions should be taken with IPLD600-12?

Always ensure power is off before installation or maintenance to prevent electrical shock.

Is IPLD600-12 compatible with other brands?

Yes, IPLD600-12 is compatible with various brands as listed in the cross-reference section.

What maintenance is required for IPLD600-12?

Regular inspections for wear and ensuring connections are secure are recommended.

What troubleshooting steps can be taken for IPLD600-12?

Check all connections and ensure the power supply is within the specified range.

What temperature range can IPLD600-12 operate in?

The operating temperature range is not specified in the document.

What is the weight of IPLD600-12?

The weight of IPLD600-12 is not provided in the document.

Frequently Asked Questions about NSI Industries

How are Tork products typically installed?

Tork products are typically installed by trained technicians who follow a comprehensive commissioning process. This includes verifying the work environment, conducting electrical installation checks, performing internal and external equipment inspections, powering on the system, and executing operational tests to ensure compatibility and reliability.

What environmental ratings do Tork products have?

Tork products are designed to meet various environmental ratings, including NEMA Type 4X and Type 6, which provide protection against corrosion, windblown dust, rain, and occasional temporary submersion. These ratings ensure that Tork products can withstand harsh industrial environments while maintaining operational integrity.

What communication protocols do Tork products support?

Tork products support a comprehensive range of communication protocols, including PROFIBUS DP V1, PROFINET with dual port, EtherNet/IP with dual port, CANopen, and Modbus RTU integrated as standard. These protocols facilitate flexible network integration and high-performance communication across various industrial automation systems.

What are the key features of Tork products?

Tork products are designed with advanced features that enhance efficiency and reliability in industrial applications. Key features include integrated harmonics and EMC design for improved power quality, removable terminals for quick installation, and USB ports for easy troubleshooting. Additionally, Tork solutions emphasize user-friendly setup with application wizards and memory modules for convenient parameter management.

What are the main product lines offered by Tork?

Tork offers a diverse range of products primarily focused on industrial automation, including TORK® Photocontrols, lighting controls, and various electrical components such as enclosures, occupancy sensors, and grounding solutions. These products are designed to enhance efficiency and reliability in commercial and industrial applications.

What technical support does Tork offer?

Tork offers a comprehensive range of technical support services, including 24/7 customer support, on-site service management, and a technical hotline network. With three advanced technical support centers and over 8,000 hours of technical training conducted annually, Tork ensures certified expertise across 25+ languages to assist customers effectively. Their commitment to service is reflected in a 98% Service Level Agreement compliance rate, providing reliable support for all operational needs.

What industries and applications are Tork products used for?

Tork products are utilized across a variety of industries, including food processing, healthcare, hospitality, and manufacturing. They are designed for applications such as hand hygiene, surface cleaning, and dispensing solutions, ensuring efficiency and compliance in environments that require high standards of cleanliness and safety.

What certifications and standards do Tork products comply with?

Tork products comply with UL and cUL certifications, ensuring they meet rigorous safety and performance standards. Additionally, many models are designed to meet NEMA enclosure ratings, providing protection against environmental factors.

How are Remke products typically installed?

Remke products are typically installed through a systematic process that includes site audits to verify proper wiring, followed by remote or on-site commissioning. This commissioning involves installation verification, programming, and communication testing to ensure the system operates reliably and meets design specifications.

What accessories are available for Remke products?

Remke offers a wide range of accessories for their products, including panel mounting kits, fuse holders for voltage inputs, ferrites for communication modules, and current transformers. These accessories enhance the functionality and protection of Remke's industrial automation solutions, ensuring reliable performance in various applications.