Clamp, PC Beam, Outer Diameter of Conduit or Pipe 1.315 Inch, Nominal Conduit Size 1 Inch, Type 316 Stainless Steel, For Mounting Pipe or Conduit Parallel to the Beam

Round Ceiling Fan Box, 6 Cubic Inches, 4 Inch Diameter, 1/2 Inch Knockouts, Pre-Galvanized, Drawn Construction, with Plastic Romex Connector Included

Octagon Ceiling Fan Box, 15.8 Cubic Inches, 4 Inch Diameter x 1-1/2 Inches Deep, 1/2 Inch Knockouts, Pre-Galvanized Steel, Drawn Construction, with Non-Metallic Cable Clamps (C-5), For use with Non-Metallic Sheathed Cable

Adjusting Ring, Brass, For 78, 88, and 98 Series Floor Boxes

Octagon Ceiling Fan Box, 15.8 Cubic Inches, 4 Inch Diameter x 1-1/2 Inches Deep, 1/2 Inch Knockouts, Pre-Galvanized Steel, Drawn Construction, with Non-Metallic Cable Clamps (C-5) and Old Work Bar Hanger with 16 Inch to 24 Inch Length, For use with Non-Metallic Sheathed Cable

Gangable Switch Box, 18 Cubic Inches, 3 Inches Long x 2 Inches Wide x 3-1/2 Inches Deep, 1/2 Inch Knockouts, Pre-Galvanized Steel, Armored Cable Clamps (C-3) and SSX Bracket for Metal Stud, For use with Armored/Metal Clad Cable

Four Compartment Raised Access Floor Module, 172 Cubic Inches, Length 10 Inches, Width 7-15/16 Inches, Depth 2-1/2 Inches, Galvanized Steel with Gray Cover, Comes with Left and Rigth Power Panels and Wiring Tunnel

Square Box Surface Cover, 5 Cubic Inches, 4 Inch Square x 1/2 Inch Deep, 1-13/32 Inch Diameter Hole, Galvanized Steel, For use with Two Single Flush Receptacles

Locknut, Conduit Size 1/2 Inch, Width 1.140 Inch, Thickness 0.125 Inch, Die Cast Zinc

Set Screw Connector, Concrete Tight, Conduit Size 3/4 Inch, Material Zinc Plated Steel, Color Red, For Fire Alarm Applications

Liquidtight Connector, Straight, 1/2 Inch, Plastic, Gray

Round Ceiling Fan Box, 6 Cubic Inches, 4 Inch Diameter, 1/2 Inch Knockouts, Pre-Galvanized, Drawn Construction, For use with Conduit

Masonry Box Partition, 3-3/4 Inches Wide x 3-1/2 Inches Deep, Galvanized Steel, Low Voltage, Drilled and Tapped for Mounting, Furnished with Two 8/32 Screws

Old Work Box Support Clip. Clips Lock Old-Work Steel Switch Boxes Tightly To Wall Plaster, Dry Wall, Concrete Block, Brick Or Concrete. Adapts To Any Wall Thickness Up To 3/4 Inch

Connector, EMT to Box Set-Screw Type Pul Elbow, Conduit Size 1/2 Inch, Height 1.31 Inch, Opening Diameter 1.10 Inch, Die Cast Zinc, Pack of 100

1-1/2 Inch, Steel Two Hole Strap-Zinc Plated, For Use with Rigid/IMC Conduit

Liquidtight Conduit Fitting, Straight, Trade Size 2-1/2 Inch, Malleable Iron

Rod, Continuous Threaded, Rod Size 3/8 Inch - 16, Length 10 Feet, Ultimate Load 1,900 Pounds, Galvanized Steel

Octagon Box, 15.8 Cubic Inches, 4 Inch Diameter x 1-1/2 Inches Deep, 1/2 Inch Knockouts, Pre-Galvanized Steel, Drawn Construction, with Armored Cable Clamps (C-3) and V Bracket, For use with Armored/Metal Clad Cable

2 Inch, Non-Metallic Insulated Bushing, For Use with Rigid/IMC Conduit

2 Inch, Steel One Hole Strap, Zinc Plated, For Use with Rigid/IMC Conduit

Set Screw Connector, Concrete Tight, Conduit Size 3-1/2 Inches, Length 3.906 Inches, Material Zinc Plated Steel, For use with EMT Conduit

Gangable Switch Box, 14 Cubic Inches, 3 Inches Long x 2 Inches Wide x 2-3/4 Inches Deep, 1/2 Inch Knockouts, Pre-Galvanized Steel, Non-Metallic Cable Clamps (C-5) and Ears Flush, For use with Non-Metallic Sheathed Cable

#12 AWG insulated fifteen-inch stranded pigtail with a captive 10-32 x 3/8 inch round head screw on one end and a fork-tongue terminal on the other end