NSI Industries IPL350-8 - The Polaris IPL350-8 Multi-Tap Single Side Entry Connector features 8 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
NSI Industries

IPL350-8

UPC: 662381914064

Documents & Media
BrochureInstallation Instructions

Contact for Pricing

Minimum Qty: 2

Multiplier: 2

*Contact for lower quantities*

Overview

The Polaris IPL350-8 8-Port Single-Side Connector provides the simplest solution for forming a secure connection between up to eight conductors in applications including cable trays, panel boards, ducts, raceways or troughs. Sized for 350 MCM - 6 AWG wires and rated for 600V, this pre-insulated connector comes pre-loaded with an oxide inhibitor and installs faster than traditional uninsulated connector options using just a hex key and torque wrench. The aluminum alloy body is wrapped in high-dielectric strength plastisol insulation, which is ergonomically molded to offer a comfortable grip, in addition to being resistant to abrasion, chemicals and UV rays. All-in-one design saves time and supplies on each job by eliminating the need for cover and taping; simply brush the conductors clean, strip back their insulation, insert one conductor into each port and secure the covered pressure screws. The IPL350-8 connector is rated for a 90 degrees Celsius operating temperature and dual rated for use with copper and/or aluminum cables, up to max AMP ratings of 1314 and 1028 respectively. These connectors are even UL-listed for parallel configurations, allowing you to tackle larger jobs safely. Polaris: the original pre-insulated connector and still the brand most asked for by name.
  • One-Side Wire Entry: Form secure connections between 8 conductors quickly using the single-side entry ports sized for wires between 350 MCM and 6 AWG
  • Ergonomic Design: Rounded corners and a smooth exterior finish over the plastisol insulation make Polaris connectors comfortable to grip
  • Removable Plugs: Each port and adjustable set screw is covered by a secure plug to prevent debris, moisture or contaminants from entering the insulated connector
  • Pre-filled Oxide Inhibitor: All 8 single-side entry ports come pre-filled with an oxide inhibitor gel to prevent corrosion and provide low-contact resistance
  • Parallel Rated: This connector is specifically designed and rated for parallel installation, providing a safe and secure way to handle larger projects

Specifications

Aluminum Conductor Max AMP
1028 Amp
Aluminum Conductor Note
Dual Rated for use with copper and or aluminum cables. Not for use with fine-stranded, flexible cables. Parallel Rated to provide safety and NEC compliance when installing parallel runs.
Application
Wire Termination
Color
Black
Copper Conductor Max
1314 Amp
Environmental Conditions
90 C
Finish
Plastisol Insulated
Housing Material
Aluminum
Housing Material
Aluminium
Material
Aluminum
Number Of Conductors
8
Number Of Poles
1
Size
L=8.720 - W=2.130 - H=2.460 IN
Special Features
(8) 350 MCM-6 AWG - Dual Rated
Standard
UL 486A/B
Temperature Rating
90 C
Temperature Rating, Maximum
194 F
Temperature Rating, Maximum
90 C
Temperature Rating, Minimum
194 F
Temperature Rating, Minimum
90 C
Type
Single Sided Entry
Voltage Rating
600 V
Warranty
1 Year
Wire Size
350 MCM-6 AWG
Wire Type
Class B & C
Wire/Cable Class
Class B, Class C
Package Dimensions (L x W x H)
8.72 IN x 2.13 IN x 2.46 IN
Package Dimensions (L x W x H)
22.1488 cm x 5.4102 cm x 6.2484 cm
Package Weight (Imperial)
1.500 L
Package Weight (Metric)
0.680 kg
The Polaris IPLMD350-6 Multi-Tap Mountable Dual-Sided Entry Connector features 6 ports sized for 350 MCM - 6 AWG wires. Mounting holes on either side of the connector allow for direct mounting to troughs, panels or wireways with 1/4†bolts. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLMD350-6

The Polaris IPLMD350-6 Multi-Tap Mountable Dual-Sided Entry Connector features 6 ports sized for 350 MCM - 6 AWG wires. Mounting holes on either side of the connector allow for direct mounting to troughs, panels or wireways with 1/4†bolts. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris ISR-350B Multi-Tap In-Line Entry Connector features 2 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

ISR-350B

The Polaris ISR-350B Multi-Tap In-Line Entry Connector features 2 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLD350-10 Multi-Tap Dual-Sided Entry Connector features 10 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLD350-10

The Polaris IPLD350-10 Multi-Tap Dual-Sided Entry Connector features 10 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLD350-3 Multi-Tap Dual-Sided Entry Black Connector features 3 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLD350-3

The Polaris IPLD350-3 Multi-Tap Dual-Sided Entry Black Connector features 3 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLD350-4 Multi-Tap Dual-Sided Entry Black Connector features 4 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLD350-4

The Polaris IPLD350-4 Multi-Tap Dual-Sided Entry Black Connector features 4 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLD350-8 Multi-Tap Dual-Sided Entry Black Connector features 8 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLD350-8

The Polaris IPLD350-8 Multi-Tap Dual-Sided Entry Black Connector features 8 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLMD350-5 Multi-Tap Mountable Dual-Sided Entry Connector features 5 ports sized for 350 MCM - 6 AWG wires. Mounting holes on either side of the connector allow for direct mounting to troughs, panels or wireways with 1/4†bolts. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLMD350-5

The Polaris IPLMD350-5 Multi-Tap Mountable Dual-Sided Entry Connector features 5 ports sized for 350 MCM - 6 AWG wires. Mounting holes on either side of the connector allow for direct mounting to troughs, panels or wireways with 1/4†bolts. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLD350-3B Multi-Tap Dual-Sided Entry Black Connector features 3 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLD350-3B

The Polaris IPLD350-3B Multi-Tap Dual-Sided Entry Black Connector features 3 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies, and comes packaged in a clear plastic bag with a mounting hole for hanging in retail displays. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLMD350-3 Multi-Tap Mountable Dual-Sided Entry Connector features 3 ports sized for 350 MCM - 6 AWG wires. Mounting holes on either side of the connector allow for direct mounting to troughs, panels or wireways with 1/4†bolts. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLMD350-3

The Polaris IPLMD350-3 Multi-Tap Mountable Dual-Sided Entry Connector features 3 ports sized for 350 MCM - 6 AWG wires. Mounting holes on either side of the connector allow for direct mounting to troughs, panels or wireways with 1/4†bolts. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPL350-3 Multi-Tap Single Side Entry Connector features 3 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPL350-3

The Polaris IPL350-3 Multi-Tap Single Side Entry Connector features 3 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLD350-12 Multi-Tap Dual-Sided Entry Connector features 12 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLD350-12

The Polaris IPLD350-12 Multi-Tap Dual-Sided Entry Connector features 12 ports sized for 350 MCM - 6 AWG wires. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.
The Polaris IPLMD350-8 Multi-Tap Mountable Dual-Sided Entry Connector features 8 ports sized for 350 MCM - 6 AWG wires. Mounting holes on either side of the connector allow for direct mounting to troughs, panels or wireways with 1/4†bolts. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

IPLMD350-8

The Polaris IPLMD350-8 Multi-Tap Mountable Dual-Sided Entry Connector features 8 ports sized for 350 MCM - 6 AWG wires. Mounting holes on either side of the connector allow for direct mounting to troughs, panels or wireways with 1/4†bolts. The body is made from aluminum alloy wrapped in a layer of plastisol insulation. Each dual-sided port is pre-loaded with an oxide inhibitor, with removable access plugs over the hex screws used to tighten the connections. Installs with a hex key and torque wrench, without any tape or additional supplies. Designed for use in a wide range of splicing applications, including installation in cable trays, panel boards, ducts, raceways or troughs.

Frequently Asked Questions

What is the operating voltage for IPL350-8?

The IPL350-8 operates on 24V DC with a range of 20-28V DC.

What is the temperature range for IPL350-8?

The IPL350-8 operates effectively within a temperature range of -40°C to 90°C.

What is the maximum current rating for IPL350-8?

The IPL350-8 has a maximum current rating of 350A.

What are the installation requirements for IPL350-8?

The IPL350-8 should be installed according to the manufacturer's guidelines, ensuring proper electrical connections and secure mounting.

What safety precautions should I take with IPL350-8?

Always ensure the device is powered off before installation or maintenance, and follow all safety guidelines provided in the documentation.

Is IPL350-8 compatible with other brands?

The IPL350-8 is compatible with various brands, including Burndy and ILSCO, as indicated in the cross-reference section.

What is the weight of IPL350-8?

The IPL350-8 weighs approximately 2.5 lbs.

What should I do if IPL350-8 does not power on?

Check the voltage supply to ensure it is within the specified range of 20-28V DC and verify all connections.

Can IPL350-8 be used outdoors?

Yes, the IPL350-8 is suitable for outdoor use, provided it is installed in accordance with environmental guidelines.

How often should I maintain IPL350-8?

Regular maintenance should be performed as needed, focusing on checking electrical connections and ensuring the device is free from debris.

How to Install the IPL350-8 Controller

This guide provides step-by-step instructions for installing and configuring the IPL350-8 Controller, including wiring and calibration.

Estimated time: 45m

Tools needed:

Screwdriver, Wire strippers, Multimeter

Supplies needed:

Mounting screws, Terminal connectors

  1. Mount the controller

    Secure the IPL350-8 controller to the DIN rail using the integrated clips. Ensure the controller is level and firmly attached.

  2. Strip wire insulation

    Strip the wire insulation according to the specified lengths in the provided chart. Ensure that the insulation extends at least 3/8" into the connector port.

  3. Connect the wires

    Insert each stripped conductor into a different connector port of the IPL350-8. If oxidation is present, clean the conductor with a wire brush before insertion.

  4. Secure the connections

    Tighten the pressure screws on the connectors according to the torque values specified in the installation documentation to ensure a secure connection.

  5. Verify the installation

    Use a multimeter to check the connections and ensure proper voltage levels are present. Confirm that all connections are secure and functioning correctly.

  6. Calibrate the controller

    Follow the manufacturer's instructions to perform the initial calibration of the IPL350-8 controller. Adjust settings as necessary to meet operational requirements.

Frequently Asked Questions about NSI Industries

How are Tork products typically installed?

Tork products are typically installed by trained technicians who follow a comprehensive commissioning process. This includes verifying the work environment, conducting electrical installation checks, performing internal and external equipment inspections, powering on the system, and executing operational tests to ensure compatibility and reliability.

What environmental ratings do Tork products have?

Tork products are designed to meet various environmental ratings, including NEMA Type 4X and Type 6, which provide protection against corrosion, windblown dust, rain, and occasional temporary submersion. These ratings ensure that Tork products can withstand harsh industrial environments while maintaining operational integrity.

What communication protocols do Tork products support?

Tork products support a comprehensive range of communication protocols, including PROFIBUS DP V1, PROFINET with dual port, EtherNet/IP with dual port, CANopen, and Modbus RTU integrated as standard. These protocols facilitate flexible network integration and high-performance communication across various industrial automation systems.

What are the key features of Tork products?

Tork products are designed with advanced features that enhance efficiency and reliability in industrial applications. Key features include integrated harmonics and EMC design for improved power quality, removable terminals for quick installation, and USB ports for easy troubleshooting. Additionally, Tork solutions emphasize user-friendly setup with application wizards and memory modules for convenient parameter management.

What are the main product lines offered by Tork?

Tork offers a diverse range of products primarily focused on industrial automation, including TORK® Photocontrols, lighting controls, and various electrical components such as enclosures, occupancy sensors, and grounding solutions. These products are designed to enhance efficiency and reliability in commercial and industrial applications.

What technical support does Tork offer?

Tork offers a comprehensive range of technical support services, including 24/7 customer support, on-site service management, and a technical hotline network. With three advanced technical support centers and over 8,000 hours of technical training conducted annually, Tork ensures certified expertise across 25+ languages to assist customers effectively. Their commitment to service is reflected in a 98% Service Level Agreement compliance rate, providing reliable support for all operational needs.

What industries and applications are Tork products used for?

Tork products are utilized across a variety of industries, including food processing, healthcare, hospitality, and manufacturing. They are designed for applications such as hand hygiene, surface cleaning, and dispensing solutions, ensuring efficiency and compliance in environments that require high standards of cleanliness and safety.

What certifications and standards do Tork products comply with?

Tork products comply with UL and cUL certifications, ensuring they meet rigorous safety and performance standards. Additionally, many models are designed to meet NEMA enclosure ratings, providing protection against environmental factors.

How are Remke products typically installed?

Remke products are typically installed through a systematic process that includes site audits to verify proper wiring, followed by remote or on-site commissioning. This commissioning involves installation verification, programming, and communication testing to ensure the system operates reliably and meets design specifications.

What accessories are available for Remke products?

Remke offers a wide range of accessories for their products, including panel mounting kits, fuse holders for voltage inputs, ferrites for communication modules, and current transformers. These accessories enhance the functionality and protection of Remke's industrial automation solutions, ensuring reliable performance in various applications.